Honda Civic Service Manual: Side Impact Sensor (First) Removal and Installation (2-door)
7521B6 LEFT FRONT
7521B7 RIGHT FRONT
![](images/books/497/ba3801558678acbff3e57341c7096d6f.png)
Removal
NOTE: SRS components are located in this area. Review the SRS component
locations and the precautions and procedures before doing repairs or service.
|
1. |
Battery Terminal (SRS) - Disconnection |
![](images/books/497/cde212f2f3050dc01ae2aa334dd230d1.png)
|
|
1.
|
Make sure the ignition switch is in LOCK (0).
|
|
2.
|
Disconnect and isolate the negative cable and battery sensor
(A) from the battery (B).
|
|
NOTE: Always disconnect the negative side first.
|
|
3.
|
Disconnect the positive cable (C) from the battery.
|
|
4.
|
Wait at least 3 minutes before starting work.
|
|
![](images/books/497/c6a98160298838b4d36064d676042475.png)
|
|
1.
|
Driver's side: Remove the lower anchor cap (A).
|
|
2.
|
Driver's side: Remove the lower anchor bolt (B).
|
|
![](images/books/497/36d18fb00aa2872addc03205024fb83e.png)
|
|
3.
|
Driver's side: Remove the cap (A).
|
|
4.
|
Driver's side: Remove the opener lock cylinder (B).
|
|
![](images/books/497/689eab9aaeef064d9f4d4346ec2a5098.png)
|
|
5.
|
Driver's side: Remove the screw (A).
|
|
Driver's side
![](images/books/497/09e4c345eade61029cd585a473c3924b.png)
Passenger's side
![](images/books/497/c08292aa467a0764a96d1808da908503.png)
|
|
6.
|
Remove the front door sill trim (A).
|
|
3. |
Side Impact Sensor (First) |
![](images/books/497/2264ab8fa4f573454dadeed4c0071980.png)
|
|
1.
|
Disconnect the side impact sensor (first) connector on the floor
wire harness.
|
|
2.
|
Remove the TORX bolt using a TORX T30 bit, then remove the side
impact sensor (first) (A).
|
|
![](images/books/497/f740376d3f9f1776a937914799e742a9.png)
Installation
NOTE: SRS components are located in this area. Review the SRS component
locations and the precautions and procedures before doing repairs or service.
|
1. |
Side Impact Sensor (First) |
![](images/books/497/b564ec7fbf6c3b3ccc459dbb7914dfd1.png)
|
|
1.
|
Install the side impact sensor (first) (A) with the new TORX
bolt using a TORX T30 bit.
|
|
2.
|
Connect the side impact sensor (first) connector on the floor
wire harness.
|
|
2. |
Battery Terminal (SRS) - Reconnection |
(o.2ao.sam.
|
NOTE: If the battery performs abnormally, test the battery.
|
|
1.
|
Clean the battery terminals.
|
|
2.
|
Connect the positive cable (A) to the battery (B).
|
|
NOTE: Always connect the positive side first.
|
|
3.
|
Connect the negative cable and battery sensor (C) to the battery.
|
|
4.
|
Apply multipurpose grease to the terminals to prevent corrosion.
|
|
![](images/books/497/7f987abb5c1fe4d2a040a9ca1bd3cb5f.png)
|
|
1.
|
Connect the HDS to the data link connector (DLC) (A) located
under the driver's side of the dashboard.
|
|
2.
|
Turn the ignition switch to ON (II).
|
|
3.
|
Make sure the HDS communicates with the vehicle. If it does not
communicate, go to the DLC circuit troubleshooting.
|
|
|
|
1.
|
Clear the DTC(s) by following the screen prompts on the HDS.
|
|
2.
|
Turn the ignition switch to LOCK (0), then wait for 10 seconds.
|
|
5. |
Confirm Proper SRS Operation |
|
Turn the ignition switch to ON (II), and check that the SRS indicator
comes on for about 6 seconds and then goes off.
|
|
Driver's side
![](images/books/497/5d890e6aceec130817cc429c89131af5.png)
Passenger's side
![](images/books/497/50e8dbd4c737ae8c2b0c008fe45ca2e5.png)
|
|
1.
|
Install the front door sill trim (A).
|
|
![](images/books/497/c6fa96916f003cd52440e2b957e14bb3.png)
|
|
2.
|
Driver's side: Install the screw (A).
|
|
![](images/books/497/b799ba0ac3e6d6d3af26b309948ef910.png)
|
|
3.
|
Driver's side: Install the opener lock cylinder (A).
|
|
4.
|
Driver's side: Install the cap (B).
|
|
@@@
|
|
5.
|
Driver's side: Assemble the washer, the collar, and the bushing
on the lower anchor bolt as shown.
|
|
NOTE: Apply medium strength liquid thread lock to the lower anchor
bolt before reinstallation.
|
|
7/1s-2om-min
|
|
6.
|
Driver's side: Install the lower anchor bolt (A).
|
|
7.
|
Driver's side: Install the lower anchor cap (B).
|
|
7521A4 LEFT FRONT
7521A8 RIGHT FRONT
Removal
NOTE: SRS components are located in this area. Review the SRS component
locations and the precautions and procedures before doing re ...
7521B6 LEFT FRONT
7521B7 RIGHT FRONT
NOTE: SRS components are located in this area. Review the SRS component
locations and the precautions and procedures before doing repairs or ...
See also:
Honda Civic Owners Manual. High Beam Headlight
Models with halogen headlights
Push the tab to remove the coupler.
Rotate the old bulb counter-clockwise to
remove.
Insert a new bulb into the headlight
assembly and turn it clockwise.
Insert the coupler into the connector of the
bulb.
Headlight Bu ...