Several attachment systems are available for securing child restraint seats in a vehicle, and the systems commonly used may differ depending on the country and applicable safety regulations. In the Seat Ibiza, the correct installation method depends on the type of child restraint, its approval category and the attachment points provided at the selected seating position. Some child seats are secured using the vehicle's seat belt, while others use ISOFIX anchorages together with an additional stabilising device. Regardless of the attachment method, the child seat must be approved for the intended installation and fitted in accordance with the manufacturer's instructions. A correctly installed restraint should remain securely positioned and provide the protection for which it was designed.
Attachment systems overview
An ISOFIX child seat is equipped with two rigid attachment clips, commonly referred to as connectors. These connectors engage with the corresponding ISOFIX anchorage rings located in the gap between the seat cushion and the backrest of the outer rear seating positions. When installing the child seat, align its connectors with the anchorage points and engage them according to the restraint manufacturer's instructions. Check that both connectors are securely locked before placing the child in the seat.
ISOFIX attachment systems are widely used in Europe and are available on many approved child restraint models. Depending on the design and approval of the child seat, the two ISOFIX connectors may need to be supplemented by a Top Tether strap or a support leg. These additional components help stabilise the restraint and must be used whenever required by the manufacturer. ISOFIX compatibility alone does not mean that every child seat can be installed in every seating position of the Seat Ibiza; the restraint's approval and vehicle compatibility information must also be checked.
Additional attachment:
Some child restraint systems require an additional securing component alongside their primary attachment method. These components are intended to improve the stability of the child seat and help control its movement during a collision. The two arrangements described below are the Top Tether strap and the support leg, also referred to as a support bracket. They serve different purposes and are not interchangeable. Always use the arrangement specified for the particular child restraint system.
The anchorage points intended for Top Tether attachment are identified by an anchor symbol. This marking helps distinguish the approved securing points from other fittings in the luggage compartment. Before connecting the strap, locate the appropriate anchorage and make sure the hook is attached to the correct point. Do not secure a Top Tether strap to an ordinary luggage hook or another component that has not been designated for child restraint attachment. Once connected, adjust the strap as instructed so that the child seat is held securely in its intended position.
The support bracket works together with the child restraint's primary attachment system to improve stability. Its effectiveness depends on correct positioning and secure contact with the floor. A support leg that is too short, incorrectly extended or resting on an unsuitable surface may not provide the intended support during a collision. The child seat manufacturer's instructions must be followed carefully when adjusting and locking the support leg.
Child seats equipped with a support bracket may be used only in compatible seating positions, such as the front passenger seat or the outer rear seats, where the particular restraint and vehicle configuration permit this installation. The centre rear seating position must not be used for the support-leg arrangement described here because the available floor clearance does not provide the required installation conditions. Before fitting this type of restraint in the Seat Ibiza, consult the child seat manufacturer's list of approved vehicles and seating positions. The compatibility list supplied with the restraint instructions identifies where the support leg can be used safely and correctly.
Recommended systems for attaching child seats
SEAT recommends selecting the child restraint attachment arrangement according to the seat's orientation and approved installation method. The following combinations are recommended for the corresponding types of child seats. In every case, the restraint must be suitable for the child's height and weight, and the selected seating position must support the required anchorage system. The child seat manufacturer's instructions take precedence when determining which attachment components are necessary for a particular model.
WARNING Incorrect installation or use of a child seat support bracket can result in serious or fatal injuries during an accident. A support leg that is not properly positioned may fail to stabilise the child restraint when subjected to collision forces. Always check that the support bracket is compatible with the selected seating position, correctly adjusted and securely installed before allowing a child to travel in the seat.
Fitting and using child seats
Securing a child seat with the ISOFIX
or i-Size systemHonda Civic Service Manual. Trunk Lid Adjustment (Except Natural Gas models)
Removal
1.
Rear Seat Cushion
1.
Remove the bolt (A) securing the rear seat cushion (B).
...