Seat Ibiza (6F) 2017-2026 Owner's Manual: Raise the vehicle

Fig. 188 Location of the designated vehicle jacking points.

Fig. 189 Cross member: correct positioning and engagement of the vehicle jack.
When changing a wheel on the Seat Ibiza, the vehicle must be raised using the designated lifting points and the
jack supplied with the vehicle. Correct jack positioning is essential to keep the car stable during the wheel
change and to prevent damage to the bodywork or underbody components. Before lifting the vehicle, make sure it
is parked securely on a firm, level surface and that the wheel nuts have been loosened slightly while the wheel
is still in contact with the ground.
- Position the jack from the vehicle tool kit on solid, stable ground capable of supporting the weight of the
vehicle without sinking or shifting.
If the ground is not sufficiently firm, place a large, strong wooden board or another suitable rigid
support beneath the jack to distribute the load more evenly. The support must be stable and large enough
to accommodate the entire jack base.
If the surface is slippery, such as smooth tiles or polished flooring, place a suitable rubber mat or
other non-slip material beneath the jack. This helps prevent the jack from moving sideways as the
vehicle is raised. Check that the supporting surface and any additional material remain securely
positioned before proceeding.
- Locate the marking on the lower cross member that identifies the designated jack support point nearest to
the wheel being changed, as illustrated in ››› Fig. 188. The correct lifting location is indicated by a
recessed area in the vehicle's lower body structure. Use the support point closest to the affected wheel
rather than choosing another convenient-looking section of the underbody.
- Place the jack directly beneath the identified support point and begin turning its crank handle. Gradually
extend the jack until the upper support tab 1, shown in ››› Fig. 189, is positioned immediately below the
corresponding recess provided in the vehicle body. At this stage, check the alignment carefully before
allowing the jack to carry the vehicle's weight.
- Adjust the jack so that the upper tab 1 engages securely with the designated recess in the cross member. At
the same time, ensure that the movable jack base 2 rests flat and firmly against the ground. The base plate
2 must be positioned vertically beneath the upper support point 1, allowing the lifting force to act in the
intended direction. If the jack is leaning, incorrectly seated or not fully supported, reposition it before
continuing.
- Once the jack is correctly aligned and stable, continue turning the crank handle slowly and evenly. Raise
the Seat Ibiza only until the wheel being changed is slightly clear of the ground. Avoid lifting the vehicle
higher than necessary, as unnecessary lifting height can reduce stability. Before removing the wheel, check
that the jack remains firmly seated at both its upper contact point and its base.
WARNING
The jack supplied with the Seat Ibiza is designed specifically for changing wheels on this vehicle model. It
must not be used to lift heavier vehicles, other types of vehicles or unrelated loads. Using the jack beyond
its intended purpose or lifting capacity can cause it to become unstable, collapse or slip, potentially
resulting in serious injury.
- Always verify that the jack is standing securely before raising the vehicle. On soft ground, the jack
base may sink under the vehicle's weight, while on smooth or slippery surfaces it may slide out of
position. Either situation can cause the vehicle to fall unexpectedly. Use a suitable firm support or
non-slip material where necessary, and never continue lifting if the jack shows signs of
instability.
- Use only the original jack supplied by the manufacturer for the Seat Ibiza. A jack intended for another
vehicle, including one approved for a different SEAT model, may have an unsuitable lifting head, support
geometry or operating range. Even if it appears to fit beneath the vehicle, it may not engage securely
with the designated support point and could slip during lifting.
- Position the jack exclusively at the designated lifting points on the lower cross member, ensuring that
its upper support is correctly aligned with the corresponding recess. Do not place the jack against an
unmarked section of the body, an unsuitable underbody component or an area that does not provide the
required engagement. Incorrect positioning may cause the jack to lose its grip, allowing the vehicle to
fall and creating a serious risk of injury.
- Never place your hands, arms, legs or any other part of your body beneath a vehicle that is supported
only by the jack. The jack is intended for temporary lifting during a wheel change and does not provide
the level of protection required for working underneath the vehicle. If the jack moves, slips or fails,
the vehicle may drop without warning.
- If any work must be carried out underneath the Seat Ibiza, support the raised vehicle with suitable,
correctly positioned axle stands designed to carry its weight. A jack alone must never be relied upon to
support a vehicle while someone is working beneath it. Ensure that the additional supports are stable
and properly positioned before entering the area underneath the vehicle.
- Never attempt to raise the vehicle when it is leaning noticeably to one side, standing on an unsuitable
incline or positioned on unstable ground. The engine must also be switched off before lifting begins. An
uneven vehicle position or a running engine can compromise stability and increase the likelihood of the
jack slipping or the vehicle moving unexpectedly.
- Do not start the engine while the vehicle is raised on the jack. Engine operation produces vibrations
that may disturb the contact between the jack and its support point. These vibrations can cause the
vehicle to shift or become dislodged from the jack, potentially resulting in a sudden fall and serious
injury.
NOTICE
- Do not lift the Seat Ibiza by placing the jack against an arbitrary section of the cross member or lower
body structure. The jack must be positioned only at the designated support points and aligned correctly
with the reinforced lifting area.
Applying the lifting force to an unsuitable location may deform the lower body structure, damage
protective panels or affect nearby components. Before raising the vehicle, confirm that the jack
head is properly engaged with the specified support point and that no surrounding trim or body panel
is carrying the load.
- The external body trim and door areas are not designed to withstand concentrated loads or support the
weight of the vehicle. Stepping on the exterior trim, placing the jack against it, leaning heavy objects
on it or applying similar pressure can cause deformation, cracking, scratches or damage to the
surrounding bodywork. Keep the jack and any additional lifting equipment clear of these areas throughout
the wheel-changing procedure. SEAT accepts no responsibility for damage resulting from improper use of
the exterior trim, doors or body components.
Fig. 186 Changing a tyre: loosening the wheel nuts with the wheel wrench.
Fig. 187 Changing a tyre: tyre valve position 1 and the correct locations for the anti-theft wheel
locking ...
Once the wheel nuts have been loosened and the Seat Ibiza has been safely raised using the jack, the wheel can be
removed and replaced. Before proceeding, make sure the vehicle is stable, the jack i ...