Honda Civic Service Manual: Moonroof Motor Removal and Installation (4-door)

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable and battery sensor (A) from the battery (B).

NOTE: Always disconnect the negative side first.

3.

Disconnect the positive cable (C) from the battery.

4.

Wait at least 3 minutes before starting work.

1.

Pull out the A-pillar trim (A) to release the clips.

2.

Put a shop towel (A) in the opening between the A-pillar trim (B) and the dashboard to prevent dropping the A-pillar clips.

3.

Disconnect the connector (A), then remove the A-pillar trim (B).

NOTE: The upper clip (C) will stay in the body.

4.

Remove the upper clip (A) from the body.

5.

Repeat on the opposite side.

1.

Remove front door opening seal (A) as needed.

2.

Repeat on the opposite side.

1.

Turn the ceiling light switch OFF.

2.

Carefully pry off the lens (A).

3.

Remove the ceiling light (B).

4.

Disconnect the connector.

1.

Driver's side: Remove the cap (A) from the front door sill trim (B).

2.

Driver's side: Remove the opener lock cylinder (C).

3.

Driver's side: Remove the screw (A).

4.

Remove both front door sill trims (A).

1.

While pushing down on the rear seat cushion (A), pull the seat hook handle (B) to release the hook (C).

2.

While pulling up the seat cushion, remove the rear door sill trim (D).

3.

The left side is shown; repeat on the right side.

1.

Remove the rear door opening seal (A) as needed.

2.

The left side is shown; repeat on the right side.

1.

Slide the front seat forward fully.

2.

Remove the B-pillar lower trim (A).

3.

The left side is shown; repeat on the right side.

1.

Remove the anchor cover (A).

2.

The driver's seat is shown; repeat on the passenger's seat.

3.

Remove the lower anchor bolt (A).

4.

The driver's seat is shown; repeat on the passenger's seat.

1.

Remove the bottom area of the B-pillar upper trim (A).

2.

The left side is shown; repeat on the right side.

3.

Remove the upper area of the B-pillar upper trim (A).

4.

The left side is shown; repeat on the right side.

5.

Pass the front seat belt lower anchor (A) out through the hole in the slider (B), then remove the B-pillar upper trim (C).

6.

The left side is shown; repeat on the right side.

1.

Remove the bolt (A) securing the rear seat cushion (B).

2.

While pushing down the rear seat cushion (A), pull the seat hook handles (B) to release the hooks (C).

3.

Remove the rear seat cushion.

1.

Remove the bolt (A) securing the rear seat side bolster (B).

2.

The left side is shown; repeat on the right side.

3.

Remove the rear seat side bolster (A).

4.

The left side is shown; repeat on the right side.

1.

Pull out the C-pillar trim (A) to release the clips.

2.

Remove the C-pillar trim.

NOTE: The front clip (B) will stay in the body.

3.

The left side is shown; repeat on the right side.

4.

Remove the front clip (A).

5.

The left side is shown; repeat on the right side.

1.

Lower the grab handle (A).

2.

Insert the tips of the push pin/grab rail cap pliers (B) into the notch.

3.

Gently squeeze the handles of the push pin/grab rail cap pliers (A), and pull the cap (B) straight out.

4.

Remove the grab handle (A).

5.

Remove the clips (A).

1.

Pull out both front door opening seals (A) as needed.

2.

Remove both kick panels (B).

1.

Push the hook (A) with a flat-tip screwdriver through the hole in the front side of the bracket cover (B).

NOTE: Make sure the hook is unlocked.

2.

While pushing in the hook (A) with a flat-tip screwdriver, release the sunvisor (B) from the holder (C), and rotate the sunvisor backward 45 °.

NOTE: Make sure the hook slides into the bracket cover as you rotate the sunvisor.

3.

Disconnect the connector (A), then remove the sunvisor (B).

NOTE: If the sunvisor cannot be removed, the hook has not rotated into the bracket cover. Repeat step 2 to rotate the hook.

4.

If necessary, turn the sunvisor holder (A) 45 ° counterclockwise, then remove it from the holder grommet (B).

5.

If necessary, remove the holder grommet (A).

1.

Turn the front individual map light switch OFF.

2.

Carefully pry off the lenses (A) with a flat-tip screwdriver.

3.

Disconnect the connector.

4.

Remove the front individual map light (B).

1.

Except K24Z7 engine: Lower the shift lever boot (A) to release the hooks from the boot.

2.

Except K24Z7 engine: Remove the shift lever knob (B).

3.

K24Z7 engine: Lower the shift lever boot (A) to release the hooks from the boot.

4.

K24Z7 engine: Loosen the shift lever boot ring (B).

5.

K24Z7 engine: Remove the shift lever knob (C).

6.

K24Z7 engine: Remove the shift lever boot ring.

1.

Remove the center console panel (A).

1.

Detach the clips (A).

2.

Remove the center console panel (A).

1.

Remove the cup holder panel assembly (A).

1.

Remove the bolts (A).

2.

Disconnect the connector (B).

3.

Remove the console box mat (A).

4.

Remove the bolts (B).

5.

Disconnect the connector (A).

6.

Remove the center console (A).

1.

M/T: Remove the center console bracket (A).

1.

Without moonroof: From the driver's A-pillar, detach the harness clips (A).

2.

Without moonroof: From under the driver's dash, disconnect the connector (A), and detach the harness clips (B).

3.

From the passenger's A-pillar, disconnect the connector (A), and detach the harness clips (B).

4.

For some models: Release the glove box stops (A) on each side of the dashboard.

5.

For some models: From the glove box opening, disconnect the connector (A), and detach the harness clip (B).

6.

From the right C-pillar, disconnect the connector (A), and detach the harness clip (B).

7.

From the left C-pillar, disconnect the terminal (A), and remove the bolt (B), then detach the harness clip (C).

8.

Remove the bolts (A) securing the shift lever assembly (B).

9.

Lay the shift lever assembly down as needed.

10.

Slide the front seat all the way back, and recline the seat-back fully.

11.

With the help of an assistant, lower the headliner (A).

12.

With the help of an assistant, remove the headliner (A) through the passenger's front door opening.

NOTE: Do not bend the headliner. Bending the headliner will crease and damage it.

1.

Remove the moonroof motor (A).

1.

Install the moonroof motor (A).

1.

With the help of an assistant, take the headliner (A) in through the passenger's front door opening.

NOTE: Do not bend the headliner. Bending the headliner will crease and damage it.

2.

With the help of an assistant, install the headliner (A).

3.

Install the bolts (A) securing the shift lever assembly (B).

4.

At the left C-pillar, connect the terminal (A), and install the bolt (B), then install the harness clip (C).

5.

At the right C-pillar, connect the connector (A), and install the harness clip (B).

6.

For some models: At the glove box opening, connect the connector (A), and install the harness clip (B).

7.

For some models: Install the glove box stops (A) on each side of the dashboard.

8.

At the passenger's A-pillar, connect the connector (A), and install the harness clips (B).

9.

Without moonroof: Under the driver's dash, connect the connector (A), and install the harness clips (B).

10.

Without moonroof: At the driver's A-pillar, install the harness clips (A).

1.

M/T: Install the center console bracket (A).

1.

Install the center console (A).

2.

Connect the connector (A).

3.

Install the bolts (A).

4.

Install the console box mat (B).

5.

Connect the connector (A).

6.

Install the bolts (B).

1.

Install the cup holder panel assembly (A).

1.

Install the center console panel (A).

2.

Install the clips (A).

1.

Install the center console panel (A).

1.

Except K24Z7 engine: Install the shift lever knob (A).

NOTE: Tighten the shift lever knob until the shift pattern is properly aligned.

2.

Except K24Z7 engine: Connect the shift lever boot (B).

3.

K24Z7 engine: Install and turn the shift lever boot ring (A) until it reaches the bottom of the threads on the shift lever.

4.

K24Z7 engine: Turn the shift lever knob (B) until the shift lever knob contacts the shift lever boot ring.

5.

K24Z7 engine: Tighten the shift lever boot ring and the shift lever knob together with the shift pattern properly aligned.

6.

K24Z7 engine: Connect the shift lever boot (C).

1.

Connect the connector.

2.

Install the front individual map light (A).

3.

Carefully install the lenses (B).

1.

Install the holder (A) into the holder grommet (B) by turning it 45 ° clockwise.

2.

Install the holder and holder grommet as an assembly into the body by pushing it until the hooks snap into place securely.

3.

Connect the connector (A), and install the sunvisor (B).

4.

While holding the bracket cover (A), rotate the sunvisor (B) forward until the hook (C) snaps into place.

5.

Gently pull down on the sunvisor to make sure it is properly secured in the body.

6.

Rotate the sunvisor into the holder (D).

1.

Install both kick panels (A).

2.

Install both front door opening seals (B) as needed.

1.

Install the clips (A) on the grab handle (B).

2.

Install the caps (C) fully into the clips.

3.

Position the grab handle (A) on the grab handle bracket (B).

4.

Push on the grab handle until the clips (C) snap into place securely.

1.

Install the new front clip (A) to the C-pillar trim (B).

2.

Install the C-pillar trim (A).

NOTE:

3.

The left side is shown; repeat on the right side.

1.

Install the rear seat side bolster (A).

2.

The left side is shown; repeat on the right side.

3.

Install the bolt (A) securing the rear seat side bolster (B).

4.

The left side is shown; repeat on the right side.

1.

Install the hooks (A) to the rear seat cushion clips (B).

2.

Install the bolt (A) securing the rear seat cushion (B).

1.

Pass the front seat belt lower anchor (A) in through the hole in the slider (B).

2.

The left side is shown; repeat on the right side.

3.

Install the upper area of the B-pillar upper trim (A).

4.

The left side is shown; repeat on the right side.

5.

Install the bottom area of the B-pillar upper trim (A).

6.

The left side is shown; repeat on the right side.

1.

Install the lower anchor bolt (A).

2.

The driver's seat is shown; repeat on the passenger's seat.

3.

Install the anchor cover (A).

4.

The driver's seat is shown; repeat on the passenger's seat.

1.

Install the B-pillar lower trim (A).

2.

The left side is shown; repeat on the right side.

1.

Install the rear door opening seal (A).

2.

The left side is shown; repeat on the right side.

1.

While pulling up the rear seat cushion (A), install the rear door sill trim (B).

2.

Push down the seat cushion, then install the hook (C) to the rear seat cushion clip (D).

3.

The left side is shown; repeat on the right side.

1.

Install both front door sill trims (A).

2.

Driver's side: Install the screw (A).

3.

Driver's side: Install the opener lock cylinder (A).

4.

Driver's side: Install the cap (B) to the front door sill trim (C).

1.

Connect the connector.

2.

Install the ceiling light (A).

3.

Carefully install the lens (B).

1.

Install front door opening seal (A).

2.

Repeat on the opposite side.

1.

Carefully install the new upper clip (A) to the A-pillar trim (B).

2.

Connect the connector (A).

3.

Fit the clips into the holes in the A-pillar.

4.

Lightly push the A-pillar trim (B) into place, then install the trim.

NOTE:

5.

Repeat on the opposite side.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery (B).

NOTE: Always connect the positive side first.

3.

Connect the negative cable and battery sensor (C) to the battery.

4.

Apply multipurpose grease to the terminals to prevent corrosion.

Resetting the moonroof is required when any of the following have occurred:

To reset the moonroof control unit, do these steps:

1.

Close the driver’s door, and keep it closed until the procedure is complete.

2.

Turn the ignition switch to LOCK (0).

3.

Press and hold the tilt switch, and turn the ignition switch to ON (II).

4.

Release the tilt switch, and turn the ignition switch to LOCK (0).

5.

Repeat steps 3 and 4 four more times.

6.

Press and hold the moonroof open switch for at least 3 additional seconds after the moonroof is fully opened.

7.

Press and hold the moonroof close switch for at least 3 additional seconds after the moonroof is fully closed (tilted).

8.

Confirm that the moonroof control unit is reset by using the moonroof AUTO OPEN and AUTO CLOSE function.