Honda Civic Service Manual: Crankshaft Pilot Bushing Replacement (R18Z1 M/T)
![](images/books/979/ba3801558678acbff3e57341c7096d6f.png)
Removal
![](images/books/979/7d4be33e83e427e7e5eb5a790000d0f3.png)
|
|
1.
|
Install the ring gear holder.
|
|
2.
|
Install the clutch alignment shaft and the remover handle.
|
|
3.
|
To prevent warping, loosen the pressure plate mounting bolts
(A) in a crisscross pattern in several steps.
|
|
4.
|
Remove the pressure plate (B).
|
|
![](images/books/979/d705a03b7c6f55f7d2391ba390416c98.png)
|
|
1.
|
Remove the clutch disc (A), the clutch alignment shaft, and the
remover handle.
|
|
3. |
Crankshaft Pilot Bushing |
![](images/books/979/3ed28427bd206e75a73c83a15b9ef602.png)
|
|
1.
|
Remove the crankshaft pilot bushing (A) using the 15 mm bearing
remover shaft set and the remover weight.
|
|
![](images/books/979/f740376d3f9f1776a937914799e742a9.png)
Installation
1. |
Crankshaft Pilot Bushing |
![](images/books/979/8e8e4db970baada5913b8d09270c3488.png)
|
|
1.
|
Install the crankshaft pilot bushing (A) into the crankshaft
using the 15 x 135L driver handle and the 22 x 24 mm bearing driver
attachment.
|
|
(pm
|
|
1.
|
Temporarily install the clutch disc onto the splines of the transmission
mainshaft. Make sure the clutch disc slides freely on the mainshaft.
|
|
2.
|
Apply super high temp urea grease (P/N 08798-9002) to the splines
(A) of the clutch disc (B).
|
|
NOTE: Wipe off any excess grease.
|
|
3.
|
Install the clutch disc using the clutch alignment shaft and
the remover handle.
|
|
![](images/books/979/a2f7a7a40a239cbe33584676ab5af4a2.png)
|
|
1.
|
Install the pressure plate (A) and the mounting bolts (B) finger-tight.
|
|
a7aag-suaa1aa
|
|
2.
|
Torque the pressure plate mounting bolts (A) in a crisscross
pattern.
|
|
NOTE:
|
|
![](images/books/979/ca917ac4d6580542ad28730916ef1daa.png)
|
Tighten the bolts in several steps to prevent
warping the diaphragm spring.
|
|
|
![](images/books/979/ca917ac4d6580542ad28730916ef1daa.png)
|
Make sure that there is no clearance between
the pressure plate and the flywheel.
|
|
|
|
Specified Torque:
|
25 N·m (2.5 kgf·m, 18 lbf·ft)
|
|
|
|
|
3.
|
Remove the ring gear holder.
|
|
4.
|
Remove the clutch alignment shaft and the remover handle.
|
|
5.
|
Make sure the diaphragm spring fingers are all the same height.
|
|
Removal
1.
Pressure Plate
1.
Install the ring gear holder.
2 ...
11010A
1.
Vehicle Lift
1.
Raise the vehicle on a lift, and make sure it is securely supported.
...