Seat Ibiza (6F) 2017-2026 Owner's Manual: Sealing and inflating a tyre
Sealing the tyre
- Unscrew the protective cap from the valve of the damaged tyre. Next, use the valve insert remover supplied
with the Tyre Mobility System, identified as component 1 in Fig. 191, to carefully unscrew and remove the
valve insert. Keep the valve insert and protective cap on a clean, dry surface where they cannot become
contaminated or lost. Dirt entering the valve may prevent it from sealing correctly when the tyre is
inflated again. Make sure the Seat Ibiza is safely parked and secured before beginning this procedure.
- Shake the tyre sealant bottle vigorously before use, as indicated by component 10 in Fig. 191. Thorough
shaking helps distribute the sealing compound evenly throughout the bottle so that it is ready to be
introduced into the damaged tyre. Follow any additional preparation instructions printed on the bottle or
provided by the Tyre Mobility System manufacturer. Do not use the sealant if its expiry date has passed or
the container is damaged.
- Take the sealant filling tube, identified as component 3 in Fig. 191, and screw it securely onto the tyre
sealant bottle. As the tube is attached, the bottle's internal seal will open automatically, allowing the
compound to flow through the filling tube. Make sure the connection is properly tightened to prevent sealant
from escaping around the bottle opening. Handle the bottle carefully once the seal has been broken, as the
contents are now ready to be transferred into the tyre.
- Remove the protective cap from the free end of the filling tube, as shown in Fig. 191, component 3. Screw
the open end of the tube onto the tyre valve until the connection is secure. Check that the tube is
correctly aligned with the valve threads and avoid forcing it into position. A properly fitted connection
helps ensure that the sealant enters the tyre rather than leaking around the valve.
- Turn the sealant bottle upside down while keeping the filling tube connected to the tyre valve. Empty the
entire contents of the bottle into the damaged tyre, following the instructions supplied with the repair
kit. Hold the bottle securely and allow sufficient time for the compound to pass through the tube. The full
quantity of sealant is required for the intended temporary repair procedure, so do not deliberately leave
part of the contents in the bottle.
- Once the sealant has been transferred, carefully unscrew the filling tube from the tyre valve and remove the
bottle. Keep the open end of the tube away from clothing and vehicle surfaces to avoid unnecessary contact
with any remaining compound. Place the used bottle and filling tube where they cannot spill or interfere
with the next stage of the repair. Do not leave the tyre valve open longer than necessary.
- Reinstall the valve insert into the tyre valve using the valve insert remover, component 1 in Fig. 191.
Carefully engage the valve insert with the tool and screw it into position, ensuring that it is correctly
seated. Avoid cross-threading or damaging the small valve components. The valve insert must be installed
securely so that the tyre can retain air when the compressor is connected. Once the insert has been
refitted, proceed with the inflation procedure without unnecessary delay.
Inflating the tyre
- Take the compressor's tyre inflation hose, identified as component 8 in Fig. 191, and screw its connector
onto the tyre valve. Make sure the hose is correctly aligned and securely attached so that compressed air
cannot escape around the connection. Position the compressor on a stable surface where it will not be
exposed to passing traffic, moving vehicle components or unnecessary tension on the hose.
- Check that the air release screw, identified as component 6 in Fig. 191, is fully closed before operating
the compressor. If the screw is open, air may escape during inflation and prevent the tyre from reaching the
required pressure. Depending on the version of the Tyre Mobility System, the air release mechanism may be
incorporated into the inflation hose. Follow the instructions for the equipment supplied with your Seat
Ibiza.
- Start the vehicle's engine and leave it running while the compressor is being operated, as specified in the
repair procedure. Before starting the engine, make sure the parking brake is applied and the transmission is
secured. On vehicles with a manual gearbox, select neutral before starting the engine; on vehicles with an
automatic transmission, keep the selector in position P. Never run the engine in an enclosed or poorly
ventilated area because exhaust gases contain dangerous substances.
- Connect the compressor's 12-volt electrical plug, identified as component 9 in Fig. 191, to the appropriate
12-volt power outlet in the vehicle. Insert the connector fully to establish a reliable electrical
connection. Route the power cable so that it is not stretched, trapped or exposed to damage during
operation. Use only the electrical connection specified for the Tyre Mobility System and make sure the
compressor is positioned safely before switching it on.
- Switch on the air compressor using the ON/OFF switch, identified as component 5 in Fig. 191. The compressor
will begin supplying air through the inflation hose into the tyre. Monitor the pressure indication while the
compressor is running and remain close enough to operate the switch when the required pressure is reached.
Do not leave the equipment operating unattended.
- Allow the compressor to run until the tyre reaches a pressure between 2.0 and 2.5 bar (29–36 psi /
200–250 kPa). Do not operate the compressor continuously for more than 8
minutes. Watch the pressure gauge during inflation and stop the compressor once the specified
range has been reached. If the tyre does not inflate sufficiently within the permitted operating time,
follow the additional procedure described below rather than allowing the compressor to run indefinitely.
- Switch off the air compressor after completing the initial inflation attempt. If the required pressure has
been achieved, prepare to disconnect the equipment and continue with the prescribed pressure-check
procedure. Be careful when handling the compressor and inflation hose, as these components may become hot
during operation. Do not touch heated parts unnecessarily.
- If the tyre cannot be inflated to the specified pressure range, unscrew the compressor's inflation hose from
the tyre valve. Disconnect it carefully to avoid damaging the valve or hose connection. The sealant may not
yet have reached the puncture, so the next step is intended to help distribute the compound inside the tyre
before another inflation attempt.
- Move the Seat Ibiza approximately 10 metres so that the sealant can spread around the
inside of the tyre and reach the damaged area. Carry out this movement slowly and only where it is safe to
do so. The short movement helps distribute the sealing compound, but it does not guarantee that the puncture
can be repaired. Stop the vehicle securely again before reconnecting the compressor.
- Reconnect the compressor's tyre inflation hose to the valve. Screw the connector on securely, ensuring that
it is correctly seated and that the hose is not twisted or damaged. Check the air release screw before
restarting the compressor. Make sure the vehicle is safely secured and that no one is standing in an unsafe
position near the wheel or inflation equipment.
- Repeat the tyre inflation procedure, monitoring the pressure gauge as the compressor operates. Attempt to
bring the tyre pressure into the required range of 2.0–2.5 bar (29–36 psi / 200–250 kPa).
Observe the compressor's operating-time restriction and allow it to cool as instructed before further use.
If the sealant has reached the puncture and formed an effective temporary seal, the tyre should now be able
to retain sufficient pressure for the next stage of the procedure.
- If the tyre still cannot reach the required minimum pressure, the damage is too extensive for the Tyre
Mobility System to seal reliably. Stop the repair attempt and do not drive the vehicle with the inadequately
inflated tyre. Continuing to drive could cause further tyre damage or lead to a sudden loss of control.
Contact an authorised SEAT Service centre, a qualified tyre specialist or a professional roadside assistance
provider.
- When the tyre has been inflated successfully, switch off and disconnect the air compressor. Carefully
unscrew the inflation hose from the tyre valve, taking care not to damage the valve threads or expose your
hands to hot components. Check that the valve is not leaking and refit its protective cap when appropriate.
Keep the repair equipment safely out of the way while preparing to continue the journey.
- If the tyre pressure is within the specified range of 2.0–2.5 bar, you may continue driving
under the restrictions applicable to a temporarily repaired tyre. Do not exceed 80 km/h (50
mph), and drive smoothly without sudden acceleration, heavy braking or aggressive cornering.
The tyre has only been temporarily sealed and must be inspected and replaced as soon as possible. Its
ability to retain pressure must be verified after the initial period of driving.
- Attach the maximum-speed warning sticker supplied with the repair kit, identified as component 2 in Fig.
191, to the instrument cluster or another suitable location within the driver's field of view. The sticker
displays the maximum permitted speed of 80 km/h (50 mph) and serves as a reminder that the
Seat Ibiza must be driven with particular caution. Position it where it can be seen easily without obscuring
important instruments or warning indicators.
- After approximately 10 minutes of driving, stop the vehicle in a safe location and check
the tyre inflation pressure again. This check is essential for determining whether the sealant has formed a
sufficiently effective temporary seal. Do not continue directly to your destination without performing the
inspection. If the pressure has fallen below the permitted limit, the vehicle must not be driven any
farther.
WARNING
The air compressor and tyre inflation hose can become very hot while the tyre is being inflated. Heat
generated during operation may cause burns if the equipment is handled carelessly. The temperature of these
components may remain elevated for some time after the compressor has been switched off. Exercise particular
caution when disconnecting the hose, moving the compressor or returning the equipment to its storage
compartment.
- Protect your hands and exposed skin from hot parts of the compressor and inflation hose. Avoid touching
heated surfaces directly, particularly after the compressor has been operating for several minutes. If
the equipment feels excessively hot, allow it to cool before handling it. Do not attempt to disconnect
components by gripping areas that may have become heated during inflation.
- Never place a hot compressor or heated flexible inflation hose on flammable materials. Contact with
combustible objects may create a fire hazard or damage the surrounding material. After use, position the
equipment on a suitable non-flammable surface while it cools, keeping it away from loose paper, fabrics
and other materials that could be affected by heat.
- Allow the compressor and inflation hose to cool sufficiently before placing them back into the Seat Ibiza
luggage compartment. Storing hot equipment immediately after use may damage nearby objects or the repair
kit's storage materials. Make sure the compressor has been switched off and disconnected from the power
outlet before packing it away. Handle the hoses and electrical cable carefully to avoid damage during
storage.
- If the damaged tyre cannot be inflated to at least 2.0 bar (29 psi / 200 kPa), the
puncture or associated tyre damage is too severe for a reliable temporary repair. The sealant has not
been able to close the damaged area sufficiently to maintain the minimum required pressure. Do not
continue driving under these conditions, even for a short distance. Driving on an inadequately inflated
tyre can cause additional structural damage, tyre failure and loss of vehicle control. Obtain assistance
from a qualified specialist or roadside recovery service.
NOTICE
To prevent overheating and possible damage to the equipment, switch off the air compressor after a maximum
of 8 minutes of continuous operation. Do not exceed this operating limit in an attempt to
inflate a tyre that is losing air. If another inflation attempt is required, allow the compressor to cool
for several minutes before switching it on again. Repeated operation without adequate cooling may damage the
compressor and prevent it from functioning when needed. Always observe the operating instructions supplied
by the Tyre Mobility System manufacturer.
Check after 10 minutes of driving
After driving for approximately 10 minutes with the temporarily repaired tyre, stop the Seat Ibiza in a safe
place and check the inflation pressure. Screw the compressor's inflation hose, identified as component
8 in Fig. 191, securely onto the tyre valve again. Read the pressure shown on the gauge,
identified as component 7. This measurement indicates whether the sealant has been able to
maintain sufficient pressure during the initial journey. The result determines whether the vehicle may continue
cautiously to a specialist workshop or must remain stationary until professional assistance is available.
1.3 bar (19 psi / 130 kPa) or lower:
- Stop the vehicle and do not continue driving. A pressure reading of 1.3 bar (19 psi / 130
kPa) or less indicates that the tyre has not been sealed sufficiently by the Tyre Mobility
System. The tyre is losing too much air to be considered safe for further use, and continuing the journey
could cause serious damage or a sudden tyre failure. Do not attempt to compensate for the continuing
pressure loss simply by driving more slowly or repeatedly inflating the tyre.
- Contact a qualified tyre specialist, an authorised SEAT Service centre or a professional roadside assistance
provider. The damaged tyre requires further inspection and an appropriate replacement or recovery procedure.
Keep the vehicle safely parked while waiting for assistance, and make sure passengers remain away from
moving traffic. Do not resume the journey until the wheel and tyre are in a condition suitable for safe
driving.
1.4 bar (20 psi / 140 kPa) and higher:
- If the pressure reading is 1.4 bar (20 psi / 140 kPa) or higher, adjust the tyre inflation
pressure to the correct specified value before continuing. Use the compressor and pressure gauge according
to the manufacturer's instructions, and make sure the tyre can retain the adjusted pressure. Do not proceed
with an incorrectly inflated tyre. The fact that the pressure remains above the minimum threshold does not
mean the puncture has been permanently repaired.
- Resume driving carefully and proceed directly to the nearest suitable specialist workshop. Do not exceed
80 km/h (50 mph), and reduce your speed further if traffic, road conditions or vehicle
handling require it. Avoid sudden acceleration, hard braking and fast cornering because the temporarily
repaired tyre may not respond in the same way as an undamaged tyre. Keep the journey as short as reasonably
possible and do not use the vehicle for unnecessary travel before the tyre has been attended to
professionally.
- Have the damaged tyre replaced by a qualified specialist as soon as possible. Inform the workshop that the
tyre has been treated with the Tyre Mobility System so that the technician is aware of the sealant inside
the tyre. The temporary repair is intended only to provide limited mobility after a puncture and must not be
regarded as a substitute for restoring the vehicle to its normal approved tyre condition.
WARNING
Driving with a tyre that has not been sealed effectively is extremely dangerous. Continued air loss can
cause the tyre to become unstable, overheat or fail unexpectedly, particularly during braking, cornering or
travel at higher speeds. A sudden tyre failure may result in loss of steering control and a serious accident
involving severe injuries. The Tyre Mobility System must only be used within its specified limitations, and
the tyre pressure must be checked after the initial 10-minute journey to establish whether continued driving
is permitted.
- Do not continue driving if the tyre pressure is 1.3 bar (19 psi / 130 kPa) or lower when
checked after the initial journey. This reading indicates that the temporary seal is insufficient and
the tyre cannot be relied upon to support safe driving. Stop the Seat Ibiza in a secure location and do
not attempt to reach a garage under the vehicle's own power with the damaged tyre in this condition.
- Seek professional assistance if the tyre cannot maintain the required pressure or the repair has not been
successful. A qualified specialist can assess the damage and arrange for the tyre to be replaced or the
vehicle to be recovered safely. Do not continue using a tyre that shows persistent air loss, visible
deformation or other signs of serious damage, even if the compressor can temporarily restore its
inflation pressure.
Fig. 191 Standard display: contents of the tyre
mobility system.
The Tyre Mobility System supplied with the Seat Ibiza is stored beneath the floor covering in the luggage
compartment. ...
See also:
Honda Civic Owners Manual. To Clear the System
Pairing codes, paired phones, all stored voice tags, all speed dial entries,
all call
history data, and all imported phonebook data are erased.
Press the button or
the button.
Rotate to select Phone
Setup, then
press .
Rotate to select System Clear, then
pr ...