Seat Ibiza (6F) 2017-2026 Owner's Manual: Rear towing eye

Fig. 157 Rear bumper on right: remove the lid.

Fig. 158 Right side of the rear bumper: towing
eye screwed in.
On Seat Ibiza vehicles equipped with a removable rear towing eye, the threaded mounting point is located on the
right-hand side of the rear bumper, behind a protective cover, as shown in Fig. 157. This cover protects and
conceals the towing eye housing during normal driving. It must be released carefully before the towing eye can
be fitted, and the attachment must be fully secured before the vehicle is used to tow another vehicle.
Vehicles supplied from the factory with a towing bracket do not have a separate threaded housing for the
removable rear towing eye behind the bumper cover. On these versions, the factory-fitted towing equipment
provides the relevant towing attachment. The tow hitch must be extended or installed, depending on its design,
and used in accordance with the applicable towing instructions. Do not attempt to install a screw-in towing eye
where no corresponding mounting point is provided.
Before using the rear towing attachment, observe the general instructions for towing and check that the selected
equipment is compatible with the vehicle. The towing eye or towing bracket must be correctly installed, and the
towing connection must be suitable for the intended operation. Particular attention should be paid to the
restrictions that apply to vehicles equipped with a factory towing bracket.
Fitting the rear towing eye
- Open the luggage compartment and take the removable towing eye from the vehicle tool kit. Make sure the
towing eye is the correct type for the Seat Ibiza and inspect its threaded section for dirt or damage before
installation. The attachment should be clean enough to screw into the mounting point without obstruction.
- Locate the protective cover on the right-hand side of the rear bumper. Press the right-hand side of the
cover, as indicated in Fig. 157, to release it from its retaining clips. Apply pressure carefully and avoid
using excessive force that could damage the cover or surrounding bumper.
- Remove the cover from its seated position and allow it to hang from its attachment to the vehicle. Do not
pull it away forcibly or place unnecessary tension on its retaining connection. Keeping the cover attached
prevents it from being misplaced while the towing eye is installed.
- Insert the towing eye into the exposed threaded housing and turn it anticlockwise, as shown
in Fig. 158. Screw it in as far as it will go, then use a suitable object to tighten it completely and
securely. Check that the towing eye is firmly seated in the mounting point before attaching the towing cable
or other permitted towing equipment. An incompletely tightened eye may loosen when subjected to pulling
forces.
- After towing has been completed, remove the towing eye by turning it clockwise. Use a
suitable object if necessary to release the attachment without damaging the bumper or threaded housing. Once
the towing eye has been removed, carefully refit the protective cover and make sure it is securely seated in
the bumper.
- Clean the towing eye if necessary, removing any accumulated dirt or moisture from the attachment and its
threads. Return it to the designated storage area in the luggage compartment alongside the other on-board
tools. Make sure it is stored securely so that it cannot move freely during normal driving.
NOTICE
- The rear towing eye must be fully screwed into its housing and firmly tightened before towing or any
permitted tow-starting operation begins. If the threaded connection is not completely engaged, the
towing eye may work loose or detach suddenly when subjected to tension. This can damage the towing
attachment, the bumper or other vehicle components. Always check that the towing eye is securely fitted
before applying a pulling force.
- If the Seat Ibiza is equipped with a factory-installed towing bracket, a rigid tow bar may only be used
when it has been specifically designed for attachment to that type of tow hitch. A conventional or
incompatible rigid tow bar can place unsuitable forces on the towing bracket and may damage both the
hitch and the vehicle. Where a suitable tow bar is unavailable, use an appropriate tow rope instead,
provided that towing is otherwise permitted and all relevant safety requirements are met.
Fig. 155 Front bumper on right: remove the lid.
Fig. 156 Right side of the front bumper: towing
eye screwed in.
The threaded mounting point for the removable front towin ...
See also:
Honda Civic Owners Manual. Tire Identification Number (TIN)
The tire identification number (TIN) is a group of numbers and letters that
look like
the example in the side column. TIN is located on the sidewall of the tire.
Tire Identification Number (TIN)
DOT B97R FW6X 2209
DOT: This indicates that the tire meets all
requirements of th ...