Honda Civic manuals

Honda Civic Service Manual: Passenger's Center Vent Removal and Installation (With Navigation)

Honda Civic Service Manual / Body / Body Interior / Trim Panels/Welts / Passenger's Center Vent Removal and Installation (With Navigation)

8411E6 RIGHT CENTER

1. Driver's Dashboard Lower Cover

1.

Remove the driver's dashboard lower cover (A).

2. Dashboard Subdisplay Visor

1.

Remove the dashboard subdisplay visor (A).

3. Audio-Navigation Unit Assembly

NOTE:

Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.

Do not work in a dusty or dirty place.

Discharge static electricity from your body before and during the work.

Do not touch the circuit board(s) with your bare hands.

Do not work with dirty hands.

Do not touch the terminal connector of the flat plate cable with your bare hands (If you have touched it, wipe it off thoroughly.).

Eject the discs before removing the audio-navigation unit to prevent damaging the CD/DVD player's load mechanism.

If you are replacing the audio-navigation unit, write down the audio presets (if possible), then enter them into the new audio-navigation unit.

When the audio-navigation unit is replaced or disconnected, do the Map Matching. This part of the initialization matches the GPS coordinates with a road on the map screen. To do this part of the procedure, make sure that the navigation system displays a map, and drive the vehicle on a mapped road shown on the map screen. Do not enter a destination at this time. When the name of the current road you are driving on appears at the bottom of the screen, the entire procedure is complete.

1.

Remove the bolts (A).

2.

Disconnect the connectors, then pull out the audio-navigation unit (A).

4. Audio-Navigation Unit Assembly

NOTE:

Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.

Do not work in a dusty or dirty place.

Discharge static electricity from your body before and during the work.

Do not touch the circuit board(s) with your bare hands.

Do not work with dirty hands.

Do not touch the terminal connector of the flat plate cable with your bare hands (If you have touched it, wipe it off thoroughly.).

Eject the disc before disconnecting the audio-navigation unit to prevent damaging the CD player's load mechanism.

If you are replacing the audio-navigation unit, write down the audio presets (if possible), then enter them into the new audio-navigation unit.

When the audio-navigation unit is replaced or disconnected, do the Map Matching. This part of the initialization matches the GPS coordinates with a road on the map screen. To do this part of the procedure, make sure that the navigation system displays a map, and drive the vehicle on a mapped road shown on the map screen. Do not enter a destination at this time. When the name of the current road you are driving on appears at the bottom of the screen, the entire procedure is complete.

1.

Remove the bolts (A).

2.

Disconnect the connectors, then pull out the audio-navigation unit assembly (A).

5. Passenger's Center Vent

1.

Remove the passenger's center vent (A).

1. Passenger's Center Vent

1.

Install the passenger's center vent (A).

2. Audio-Navigation Unit Assembly

1.

Connect the connectors, then install the audio-navigation unit assembly (A).

NOTE: Make sure all the connectors and the antenna lead are securely connected.

mm3.72.7

2.

Install the bolts (A).

3. Audio-Navigation Unit Assembly

1.

Connect the connectors, then install the audio-navigation unit (A).

NOTE: Make sure all the connectors and the antenna lead are secure.

mm3.72.7

2.

Install the bolts (A).

4. Dashboard Subdisplay Visor

1.

Install the dashboard subdisplay visor (A).

5. Driver's Dashboard Lower Cover

1.

Install the driver's dashboard lower cover (A).

Driver's Vent Removal and Installation
Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition switch is in LOCK (0). ...

Driver's Kick Panel Removal and Installation
8571G3 DRIVER SIDE Removal 1. Front Door Sill Trim - 4-Door 1. Remove the cap (A) from the front doo ...

See also:

Honda Civic Service Manual. Front Seat Belt Removal and Installation - Driver's Seat (2-door)
Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition switch is in LOCK (0). ...

© 2016-2024 Copyright www.hocivic.com

0.0259