Honda Civic manuals

Honda Civic Service Manual: Front Seat-Back Cover Removal and Installation - Driver's Seat

Honda Civic Service Manual / Body / Seating / Front Seat-Back Cover Removal and Installation - Driver's Seat

8601A9 LEFT

Removal

1. Battery Terminal (SRS) - Disconnection

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable and battery sensor (A) from the battery (B).

NOTE: Always disconnect the negative side first.

3.

Disconnect the positive cable (C) from the battery.

4.

Wait at least 3 minutes before starting work.
2. Front Seat Belt Lower Anchor Bolt - Driver's Side

2-door

1.

Remove the lower anchor cap (A).

2.

Remove the lower anchor bolt (B).

4-door

1.

Remove the anchor cover (A).

2.

Remove the lower anchor bolt (A).
3. Head Restraint

1.

Remove the headrest restraint (A).
4. Front Seat - Driver's Side

1.

Remove both seat track end covers (A).

Front side

Rear side

2.

Remove the seat mounting bolts (A).

Power seat

Manual seat

3.

Disconnect the connectors (A).

4.

Detach the clips (B).
5. Front Seat-Back As Needed - Driver's Side

2-door, 4-door (power seat)

4-door (manual seat)

1.

Release the strap(s) (A).

2-door, 4-door (manual seat)

4-door (power seat)

2.

Detach the connector clip (A) and the harness clips (B), and release the holder(s) (C).

3.

With seat heater: Disconnect the connector (D), and detach the harness clip(s) (E), then release the holder(s) (F).

4.

Unzip the seat-back cover (A).

5.

Release the hook strip (B).

6.

Release the hook strips (A).

7.

Detach the harness clip(s) (A).

8.

Pull out the harness(es) (B).

9.

Release airbag attachment wires A and B.

10.

Release the hooks (A).
6. Headrest Guides

1.

Remove the headrest guides (A).
7. Front Seat-Back Cover/Pad - Driver's Side

1.

Remove the seat-back cover/pad (A).
8. Front Seat-Back Cover - Driver's Side

1.

Remove the airbag attachment wires A and B.

Except Si (Fabric)

Except Si (Leather)

Si

2.

Remove the upholstery rings (A).

3.

Remove the seat-back cover (B).

Installation

1. Front Seat-Back Cover - Driver's Side

NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D).

1.

Install the airbag attachment wires A and B.

Except Si (Fabric)

Except Si (Leather)

Si

2.

Install the seat-back cover (A) with the upholstery rings (B).
2. Front Seat-Back Cover/Pad - Driver's Side

1.

Install the seat-back cover/pad (A).
3. Headrest Guides

1.

Install the headrest guides (A).
4. Front Seat-Back As Needed - Driver's Side

1.

Install the hooks (A).

2.

Install airbag attachment wires A and B.

3.

Install the harness clip(s) (A).

4.

Install the harness(es) (B).

5.

Install the hook strips (A).

6.

Zip the seat-back cover (A).

7.

Install the hook strip (B).

2-door, 4-door (manual seat)

4-door (power seat)

8.

Install the connector clip (A), the harness clip(s) (B), and the holder(s) (C).

9.

With seat heater: Connect the connector (D), and install the harness clip(s) (E) and the holder(s) (F).

2-door, 4-door (power seat)

4-door (manual seat)

10.

Install the strap(s) (A).
5. Front Seat - Driver's Side

Power seat

Manual seat

1.

Connect the connectors (A).

2.

Install the clips (B).

Front side

mmu....in

Rear side

3.

Install the seat mounting bolts (A).

NOTE:

Tighten the bolts by hand first, then tighten them to the specified torque.

Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten 1 and 2, then slide it forward and tighten 3 and 4.

4.

Install both seat track end covers (A).
6. Head Restraint

1.

Install the headrest restraint (A).
7. Front Seat Belt Lower Anchor Bolt - Driver's Side

2-door

1.

Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.

NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

2.

Install the lower anchor bolt (A).

3.

Install the anchor cover (B).

nmimm

4-door

1.

Install the lower anchor bolt (A).

2.

Install the anchor cover (A).
8. Battery Terminal (SRS) - Reconnection

(o.2ao.sam.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery (B).

NOTE: Always connect the positive side first.

3.

Connect the negative cable and battery sensor (C) to the battery.

4.

Apply multipurpose grease to the terminals to prevent corrosion.
Front Seat Removal and Installation - Passenger's Seat
8521D0 PASSENGER SIDE Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition sw ...

Front Seat-Back Cover Removal and Installation - Passenger's Seat ('13-'14)
SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Battery Term ...

See also:

Honda Civic Owners Manual. Emergency Engine Stop
Models with smart entry system The ENGINE START/STOP button may be used to stop the engine due to an emergency situation even while driving. If you must stop the engine, do either of the following operations:  Press and hold the ENGINE START/STOP button for about two seconds.  F ...

Nissan Kicks - OM - Seats - Wheels and tires - Audio system -
© 2016-2026 Copyright www.hocivic.com

0.0247