Seat Ibiza (6F) 2017-2026 Owner's Manual: Cleaning the exterior
The following recommendations explain how to clean and maintain the individual exterior components of your Seat
Ibiza. Different materials and surfaces require different cleaning methods, so choosing an appropriate product
and using it correctly is essential to preserving their appearance and condition. Regular cleaning also helps
prevent dirt, road salt and other contaminants from causing premature deterioration.
If you have questions about a particular cleaning procedure, encounter stubborn contamination or need to care for
a component that is not covered below, consult a qualified specialist workshop. An authorised SEAT Service
centre can also advise you on suitable cleaning products and maintenance methods for the materials fitted to
your vehicle.
Always observe the general vehicle cleaning precautions, particularly those concerning cleaning chemicals,
high-pressure washing equipment and delicate surfaces. Pay special attention to the following components and the
recommended methods for removing different types of contamination.
Windscreen wipers
- Dirt: Clean the windscreen wiper blades carefully using a soft cloth moistened with a
suitable windscreen cleaning product. Gently wipe along the rubber wiping edges to remove accumulated dirt
and deposits without stretching, twisting or damaging the blades. Avoid abrasive materials and aggressive
cleaning agents, as these may affect the rubber and reduce wiping performance.
Headlights / Tail lights
- Dirt: Wash the exterior surfaces of the headlights and rear lights with a soft sponge and a
mild, neutral soap solution. Remove dust, road grime and insect remains using gentle movements and plenty of
water. Do not use abrasive pads or harsh chemicals, which may scratch or damage the transparent light
covers. Rinse away any remaining cleaning solution after washing.
Sensors / Camera lenses
- Dirt: Keep the exterior sensors and camera lenses clean so that dirt does not obstruct
their operation. These components have sensitive surfaces and must be cleaned carefully, without applying
excessive pressure or using abrasive materials.
- Sensors: Remove dirt with a clean, soft cloth and a suitable solvent-free cleaning
product. Wipe the sensor surface gently, avoiding scratching or damaging its outer covering. Do not
use aggressive chemical cleaners or concentrated water jets directly on the sensor.
- Camera lenses: Use a soft, clean cloth with an alcohol-free cleaning product
suitable for delicate optical surfaces. Carefully remove dirt or deposits without rubbing
forcefully. A clean camera lens is important for maintaining a clear image, particularly on a Seat
Ibiza equipped with camera-based driver assistance or parking functions.
- Snow/ice: Carefully remove loose snow using a soft hand brush. For ice, use a suitable
solvent-free de-icing spray, following the product manufacturer's instructions. Avoid sharp tools, hard
scrapers or excessive force, as these may damage sensor housings, camera lenses or their protective
surfaces. Make sure the affected components are clear before using the corresponding vehicle functions.
Wheels
- Road salt: Rinse the wheels thoroughly with clean water to remove salt deposits,
particularly after driving on roads treated during winter. Pay attention to areas where salt and dirt can
accumulate. Regular removal of these deposits helps protect the wheel finish and reduces prolonged exposure
to corrosive substances.
- Brake abrasion dust: Remove accumulated brake dust using a cleaning product specifically
intended for wheels and free from acids. Follow the cleaner manufacturer's instructions and use a suitable
soft cleaning tool where necessary. Brake dust can adhere firmly to wheel surfaces, so regular cleaning
helps prevent deposits from becoming increasingly difficult to remove. Rinse the wheels thoroughly after
treatment.
Exhaust pipe ends
- Road salt: Remove road salt and ordinary dirt from the exhaust pipe ends using water. If
deposits remain, use a suitable fine-steel cleaning product where appropriate for the surface, or choose a
non-abrasive, non-corrosive cleaner. Clean carefully to avoid scratching or damaging the finish. Allow the
exhaust system to cool completely before touching or cleaning its exposed components, as these parts can
become extremely hot during vehicle operation.
Covers / Trims
- Dirt: Clean exterior covers and decorative trim with a neutral soap solution and a soft
cloth or sponge. For more persistent deposits, a suitable fine-steel cleaning product may be used where the
material and finish permit it. Check the compatibility of the product before application, since painted,
plastic and metallic trim may require different treatment. Avoid abrasive cleaning methods that could leave
scratches or alter the original appearance.
Pain
- Paint flaws: Small chips and other minor defects in the paintwork should be repaired using
a touch-up product that matches the original vehicle colour. Have the paint colour code checked by an
authorised SEAT Service centre before selecting a touch-up pencil. Correct colour matching and careful
application help make the repair less noticeable while protecting the exposed area against further
deterioration.
- Spilled fuel: Immediately rinse any fuel that comes into contact with the painted bodywork
using plenty of clean water. Do not allow fuel residues to remain on the surface, as prolonged contact may
affect the paint finish. Remove the contamination promptly and gently, without rubbing it into the
surrounding paintwork.
- Environmental rust deposits: Remove superficial rust-coloured deposits caused by
environmental contamination using a suitable rust-removing product intended for automotive paintwork. After
cleaning the affected area, apply hard wax where appropriate for the paint finish to help restore surface
protection. If you are uncertain whether the marks are superficial deposits or actual corrosion, consult a
specialist workshop before attempting treatment.
- Corrosion: If corrosion is present on the bodywork, arrange for a qualified specialist
workshop to inspect and repair the affected area. Rust that has developed beneath the paint or damaged the
underlying metal requires appropriate professional treatment. Simply cleaning or covering the visible marks
may not address the cause of the corrosion or prevent it from progressing.
- Water no longer forms droplets on clean paintwork: If water stops beading on a thoroughly
cleaned painted surface, the existing protective treatment may have deteriorated. For conventional glossy
paintwork, maintain the finish with a suitable hard wax at least twice a year. Apply the product according
to its instructions and ensure it is compatible with the vehicle's paint. Do not use hard wax on
matte-painted surfaces.
- Paintwork remains dull despite regular maintenance: If conventional glossy paint has lost
its shine and ordinary cleaning or care products no longer restore its appearance, treat it with a suitable
wax. If the selected wax does not contain protective or preservative ingredients, apply an appropriate paint
preservative afterwards. Choose products intended for the specific finish and avoid unnecessary abrasive
treatments. Matte paintwork must not be polished or treated with products designed to increase gloss.
- Stains and stubborn deposits, such as insect remains, bird droppings, tree sap and road
salt: Remove these contaminants as quickly as possible because prolonged contact can damage the
paintwork, especially in warm weather or direct sunlight. Thoroughly soak the affected area with water to
soften the deposits, then gently lift them away using a clean microfibre cloth. Avoid scraping or vigorous
rubbing, which may scratch the surface.
- Grease-based contamination, including cosmetics and sunscreen: Remove oily or greasy marks
promptly with a mild, neutral soap solution and a soft cloth. Work gently to lift the contamination without
spreading it across the surrounding paintwork. Rinse the cleaned area as appropriate and avoid using
aggressive degreasers or solvents that could damage the finish.
Carbon fibre parts
- Dirt: Clean exterior carbon fibre components using the same gentle methods recommended for
painted bodywork. Use a soft cloth or sponge with a suitable mild cleaning product, and avoid abrasive
materials or harsh chemicals. Treat the visible surface carefully to preserve its finish and prevent
scratches or other cosmetic damage.
Decorative laminates
- Dirt: Wash decorative laminated surfaces with a soft sponge and a neutral soap solution.
Remove accumulated dust and road grime using light pressure, then rinse away any cleaning residue. Do not
use aggressive solvents, abrasive sponges or polishing compounds that could damage the decorative layer or
change its appearance.
Regular, thorough and careful maintenance of the exterior and interior helps preserve the appearance, condition
and resale value of your Seat Ibiza. Dirt, environmental contamination and unsuitable ...
The interior of the Seat Ibiza contains a variety of materials, including plastics, fabrics, decorative surfaces
and, depending on equipment, artificial or natural leather. Each material has particu ...
See also:
Honda Civic Owners Manual. Driver Information Interface
The driver information interface shows the odometer, trip meter, outside
temperature indicator, and other gauges.
It also displays important messages such as warnings and other helpful
information.
Switching the Display
Main displays
Press the (display/information)
button and press ...