Seat Ibiza (6F) 2017-2026 Owner's Manual: Changing bulbs
Tail light bulbs located in the bodywork

Fig. 162 Luggage compartment: access to the
bolt securing the tail light unit.

Fig. 163 Retaining tabs on the reverse side of
the tail light.
To replace a defective bulb in a tail light assembly mounted in the bodywork of your Seat Ibiza, follow the
procedure below. Handle the light unit carefully throughout removal and installation to prevent damage to its
housing, electrical connections, or the surrounding bodywork.
- Identify which bulb has stopped working before removing the tail light assembly. Check the relevant lighting
function to determine which bulb requires replacement.
- Open the rear lid to gain access to the inner mounting area of the tail light unit.
- Locate the access cover inside the luggage compartment. Insert the flat blade of a screwdriver into the
designated recess and carefully lever off the cover ››› Fig. 162 1. Apply gentle pressure to avoid damaging
the surrounding trim.
- Disconnect the electrical connector from the tail light assembly at position 2. Release the connector
carefully without pulling directly on the wiring.
- Remove the securing bolt at position 3 by unscrewing it by hand or with a suitable screwdriver, depending on
how tightly it is fitted.
- Carefully withdraw the tail light assembly from the vehicle body by pulling it gently toward you. Keep the
unit properly supported as it comes free, then place it on a clean, smooth surface to protect the lens and
housing.
- Release the retaining tabs marked A on the rear of the light assembly ››› Fig. 163. Once the tabs have been
disengaged, carefully separate the bulb holder from the light housing.
- Remove the defective bulb and install a suitable replacement. Make sure the new bulb is correctly seated in
its holder and that the electrical contacts are properly positioned.
- Reassemble the tail light unit by following the removal procedure in reverse order. Pay particular attention
when reinstalling the bulb holder, ensuring that all retaining tabs engage securely with an audible click.
Refit the light assembly, tighten its securing bolt, reconnect the electrical connector, and replace the
access cover. Check that the repaired light operates correctly.
NOTICE
Exercise particular care when removing or reinstalling the rear light assembly. Contact between the housing
and the surrounding body panels may scratch the paintwork or damage the light unit, its mounting points, or
other nearby components. Avoid forcing the assembly if it does not release easily.
Note
- Before removing the tail light assembly, prepare a clean, soft cloth and place it beneath the unit when
setting it down. This will help protect the outer lens and other exposed surfaces from scratches while
the bulb is being replaced.
- On Seat Ibiza models equipped with LED rear lighting, only the turn signal and reversing light bulbs can
be replaced individually. The remaining LED light sources are not intended for separate bulb replacement
using this procedure.
Number plate light
The number plate lighting unit can be removed from its mounting position to replace a conventional bulb. Work
carefully around the light housing and its surrounding trim, particularly when releasing the retaining
mechanism.
- Locate the designated slot in the number plate light housing. Insert the flat blade of a suitable
screwdriver into the slot and carefully lever the light unit out of its mounting opening. Avoid applying
excessive pressure to the surrounding surface.
- Remove the bulb holder from the light assembly by rotating it in the release direction until it disengages
from the housing. Withdraw the holder carefully to expose the bulb.
- Remove the defective bulb and fit a replacement of the appropriate type. Check that it sits securely in the
holder and makes proper contact.
- Insert the bulb holder back into the light housing and rotate it until it is fully seated and securely
locked in position.
- Position the number plate light assembly in its original mounting opening and press it gently into place
until the retaining mechanism engages with an audible click. Make sure the housing sits correctly and check
that the number plate illumination works.
Note
Depending on the equipment fitted to your Seat Ibiza, the number plate lights may use LED technology instead
of conventional replaceable bulbs. These LED light sources are designed for a particularly long service
life, with an expected lifespan that may exceed that of the vehicle itself. If an LED number plate light
stops working, have the affected lighting unit inspected and replaced by an authorised workshop rather than
attempting to replace the individual LED components.
Replacing a vehicle light bulb requires a certain level of practical experience, particularly when access to the
light assembly is restricted or other components must be removed. Incorrect handling ...
Interior light and front reading lights
Fig. 164 Front reading light.
The front interior lighting assembly contains the reading lights and central interior light. When replacing a
conventi ...
See also:
Honda Civic Owners Manual. Side Curtain Airbags
The side curtain airbags help protect the heads of the driver and passengers
in the
outer seating positions during a moderate-to-severe side impact. The side
curtain
airbags equipped in this vehicle are also designed to help reduce the likelihood
of
partial and complete ejection of vehicle ...