Seat Ibiza (6F) 2017-2026 Owner's Manual: Adjusting the headrests

Fig. 65 Front seat: adjusting the headrest.

Fig. 66 Rear headrest: adjusting the headrest.
Adjusting the height of the headrests
The headrests in the Seat Ibiza can be adjusted vertically to provide suitable support for occupants of different
heights. Correct adjustment helps position the headrest behind the head, reducing the risk of neck injuries
during a collision or sudden vehicle movement. Before setting off, check that each occupied seat has its
headrest adjusted appropriately and that the locking mechanism is securely engaged.
- Hold the headrest firmly by both sides using your hands, then pull it upwards until it reaches the required
height. Raise it carefully, keeping the movement straight so that the support rods remain correctly aligned
with their guides.
To lower the headrest, hold it in the same way while pressing the release button marked 1 on the side of
the headrest mounting, as illustrated in Fig. 65 and Fig. 66. Keep the button pressed while moving the
headrest downwards to the desired position. Release the button once the appropriate height has been
reached.
- Make sure the headrest engages securely in one of its available adjustment positions. After adjusting its
height, check that it is properly locked and does not move freely downwards. The headrest must remain firmly
secured during normal driving and should be positioned to provide effective support for the occupant's head.
Removing and fitting the headrests

Fig. 67 Front headrest: removal.

Fig. 68 Rear headrest: removal.
Removing the front headrests
The front headrests of the Seat Ibiza can be removed when necessary by releasing their retaining mechanism. Carry
out this procedure only while the vehicle is stationary and ensure that there is enough clearance above the seat
to lift the headrest out without striking the roof lining or other interior components.
- Lower the headrest if necessary to gain access to the release mechanism beneath it. Check the position of
the headrest and identify the retaining button before attempting to remove it.
- Locate the release button underneath the headrest and press it in the direction indicated by arrow 1 in Fig.
67. This releases the retaining mechanism that normally prevents the headrest from being withdrawn from the
seat backrest.
- While the retaining mechanism is released, carefully pull the headrest upwards in the direction indicated by
arrow 2. Guide the support rods out of their mountings without twisting or forcing them, and take care not
to damage the surrounding upholstery or interior trim.
Fitting the front headrests
When reinstalling a front headrest, ensure that it is returned to the correct seat and that both support rods are
properly aligned with their mounting guides. The headrest must be securely fitted before the corresponding
seating position is used.
- Position the headrest above the guides in the corresponding seat backrest. Align its support rods with the
guide openings and insert them carefully, keeping the headrest straight to avoid placing unnecessary
pressure on the mounting components.
- Push the headrest downwards until the support rods engage in the retaining mechanism. Check that the
headrest is securely attached and cannot be pulled out unintentionally. Do not use the seat if the headrest
has not locked correctly.
- Adjust the installed headrest to suit the occupant's height, following the instructions for the correct
seating position. Its upper edge should be approximately level with the top of the occupant's head, as close
as possible to eye level, with the back of the head positioned near the supporting surface.
Removing the rear headrests
To remove a rear headrest from the Seat Ibiza, the corresponding section of the rear seat backrest must first be
folded partially forwards. This provides the clearance needed to withdraw the headrest from its mounting without
bringing it into contact with the vehicle's roof lining. The rear headrest retaining mechanism includes a
release button and an additional safety opening, both of which must be operated during removal.
- Release the locking mechanism of the corresponding rear seat backrest and fold it partially forwards. Move
the backrest carefully and make sure that the seat belt does not become trapped or damaged during the
adjustment.
- Raise the headrest to its highest adjustment position. This exposes the maximum available length of the
support rods and prepares the headrest for removal from its guides.
- Press and hold release button 1 shown in Fig. 68. At the same time, insert a flat-bladed screwdriver no
wider than 5 mm into the safety opening marked 2 and press the retaining mechanism. While both release
points are operated, carefully withdraw the headrest upwards from the backrest. Avoid applying excessive
force or allowing the screwdriver to damage the surrounding trim.
- Return the rear seat backrest to its upright position and move it backwards until its locking mechanism
engages correctly, following the procedure described in the section "Folding down and raising the rear seat
backrest." Check that the backrest is securely locked and that the red locking indicator is no longer
visible.
Fitting the rear headrests
When reinstalling the outer rear headrests, partially fold the corresponding rear seat backrest forwards to
provide sufficient clearance for insertion. Each headrest must be fitted into the correct mounting guides and
securely retained before the rear seating position is occupied. Take care to keep the support rods aligned and
avoid contact with the roof lining or adjacent seat components.
- Unlock the corresponding rear seat backrest and fold it partially forwards. Ensure that the backrest can
move freely and that no seat belt or other object is caught in its path.
- Align the headrest support rods with the guides in the backrest and carefully insert them. Push the headrest
into position until the retaining mechanism engages with an audible click. Once correctly fitted, the
headrest must be securely attached and must not be removable simply by pulling it upwards without operating
the release mechanism. Check that both support rods are properly seated.
- Raise the rear seat backrest to its normal upright position and push it back until the locking mechanism
engages securely, as described in the section "Folding down and raising the rear seat backrest." Verify that
the backrest is firmly locked before using the seat, then adjust the headrest height to suit the occupant.
WARNING The rear headrests of the Seat Ibiza should only be removed when their removal is
necessary for the correct installation of a child seat. Do not remove them merely to create additional space
or leave them detached while the corresponding seating positions are in use. As soon as the child seat has
been removed, reinstall the rear headrest immediately and ensure that it is properly secured and adjusted.
Travelling without a correctly installed headrest can significantly increase the risk of serious head and
neck injuries in an accident or during sudden braking.
The following instructions describe how to adjust and remove the headrests fitted to the Seat Ibiza. Correct
headrest positioning is an important part of establishing a safe seating position for eve ...