Honda Civic manuals

Honda Civic Service Manual: Rear Seat-Back Removal and Installation - Split Fold Down type (2-door)

Honda Civic Service Manual / Body / Doors and Enclosures / Doors / Rear Seat-Back Removal and Installation - Split Fold Down type (2-door)

Removal

1. Right Rear Seat-Back - Split Fold Down

1.

Remove the right rear seat-back (A).
2. Center Pivot Bracket - Split Fold Down

1.

Remove the center pivot bracket (A).

2.

If necessary, remove the bushing (B).
3. Left Rear Seat-Back - Split Fold Down

1.

Remove the bolt (A) securing the left rear seat-back (B).

2.

Extend the center seat belt (A), then remove the left rear seat-back (B).
4. Bushing

1.

If necessary, remove the bushing (A) from the center pivot bracket (B).
5. Front Seat Belt Lower Anchor Bolt - 2-Door

1.

Remove the lower anchor cap (A).

2.

Remove the lower anchor bolt (B).
6. Front Door Sill Trim - 2-Door

1.

Remove the cap (A).

2.

Remove the opener lock cylinder (B).

3.

Remove the screw (A).

4.

Remove the front door sill trim (A).
7. Rear Seat Cushion

1.

Remove the bolt (A) securing the rear seat cushion (B).

2.

While pushing down the rear seat cushion (A), pull the seat hook handles (B) to release the hooks (C).

3.

Remove the rear seat cushion.
8. Both Quarter Pillar Trims

1.

Remove the cap (A) and the clip (B).

2.

The left side is shown; repeat on the right side.

3.

Lower the coat hanger hook (A), then remove the screw (B).

4.

The left side is shown; repeat on the right side.

5.

Pull out the quarter pillar trim (A) to release the clips.

6.

Remove the quarter pillar trim.

NOTE: The rear clip (B) will stay in the body.

7.

The left side is shown; repeat on the right side.

8.

Remove the rear clip (A).

9.

The left side is shown; repeat on the right side.
9. Rear Shelf Trim

1.

Fold down the seat-back(s).

2.

From the trunk compartment, disconnect the connector (A).

3.

From the trunk compartment, detach the clips (A).

4.

Release the hooks (A).

5.

Pull out both rear seat belts (A) and the rear center seat belt (B) through the slits in the rear shelf trim (C), then remove the rear shelf trim.
10. Rear Side Trim Panel

1.

Remove the rear side trim panel (A).
11. Pivot Bracket - Split Fold Down

1.

Remove the pivot bracket (A).

Installation

1. Pivot Bracket - Split Fold Down

1.

Install the pivot bracket (A).
2. Rear Side Trim Panel

1.

Install the rear side trim panel (A).
3. Rear Shelf Trim

1.

Slip the rear seat belts (A) and the rear center seat belt (B) through the slits in the rear shelf trim (C).

2.

Install the hooks (A).

3.

Install the clips (A).

4.

From the trunk compartment, connect the connector (A).

5.

Raise the seat-back(s).
4. Quarter Pillar Trim - Check

1.

If the side curtain airbag has deployed, replace the quarter pillar trim with a new one.

2.

If the side curtain airbag has not deployed, check the quarter pillar trim (A) and note the following items:

To prevent the side curtain airbags from deploying improperly and possibly causing injury, inspect the quarter pillar trim and replace it with a new one if it has any of the following damage:

-

Any cracks, deformations, or stress-whitening in the quarter pillar trim

-

Any cracks or stress-whitened areas in the clip seating surfaces (B)

After checking and adjusting the overlap between the headliner and the quarter pillar trim, replace the rear clip (C) with a new one.

If the clips (D) are damaged or stress-whitened, replace them with new ones.
5. Headliner/Pillar Trim Overlap - Check

tms

Checking and Adjusting the Headliner/Pillar Trim Overlap

To prevent the side curtain airbag from deploying and damaging the pillar trim (A-pillar trim, B-pillar trim, C-pillar trim, quarter pillar trim), the overlap between the headliner and pillar trim must be less than 8 mm (0.31 in). To check the overlap, do this:

1.

Install the headliner (A) and the pillar trim (B).

2.

Apply masking tape (A) to the headliner (B) to mark the upper edge of the pillar trim (C).

sun:orlessthan

3.

Remove the pillar trim, and measure the headliner overlap.

If the overlap is less than 8 mm (0.31 in), remove the tape, and install the pillar trim.

If the overlap is more than 8 mm (0.31 in), go to step 4.

slmws

4.

Carefully trim the headliner with a utility knife, reducing the overlap to less than 8 mm (0.31 in).

5.

Remove the tape, and install the pillar trim.
6. Both Quarter Pillar Trims

1.

Install the new rear clip (A) to the quarter pillar trim (B).

2.

Fit the clips into the holes in the quarter pillar.

3.

Lightly push the quarter pillar trim (A) into place, then install the trim.

NOTE:

Make sure the side curtain airbag is not tucked under the clips or the ribs.

Do not push too hard on the quarter pillar trim. If you push too hard, the clip will be damaged, and it will not hold the trim properly.

Gently tug on the quarter pillar trim to verify that all clips are securely fastened.

4.

Install the screw (A).

5.

Install the clip (A) and the cap (B).
7. Rear Seat Cushion

1.

Install the hooks (A) to the rear seat cushion clips (B).

2.

Install the bolt (A) securing the rear seat cushion (B).
8. Front Door Sill Trim - 2-Door

1.

Install the front door sill trim (A).

2.

Install the screw (A).

3.

Install the opener lock cylinder (A).

4.

Install the cap (B).
9. Front Seat Belt Lower Anchor Bolt - 2-Door

@@@

1.

Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.

NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

7/1s-2om-min

2.

Install the lower anchor bolt (A).

3.

Install the lower anchor cap (B).
10. Bushing

1.

If necessary, install the bushing (A) to the center pivot bracket (B).
11. Left Rear Seat-Back - Split Fold Down

1.

Extend the center seat belt (A), then install the pivot shaft (B) to the center pivot bracket (C).

2.

Install the left rear seat-back (A).
12. Center Pivot Bracket - Split Fold Down

1.

If necessary, install the bushing (A).

2.

Install the center pivot bracket (B).
13. Right Rear Seat-Back - Split Fold Down

1.

Install the right rear seat-back (A).
Rear Power Window Switch Removal and Installation (4-door)
744120 LEFT REAR 744130 RIGHT REAR Removal 1. Rear Door Power Window Switch Panel ...

Rear Seat-Back Removal and Installation - Split Fold Down type (4-door)
Removal 1. Right Rear Seat-Back - Split Fold Down 1. Remove the ...

See also:

Honda Civic Owners Manual. Installing a Child Seat with a Lap/Shoulder Seat Belt
1. Place the child seat on the vehicle seat. 2. Route the seat belt through the child seat according to the seat manufacturer’s instructions, and insert the latch plate into the buckle. Insert the latch plate fully until it clicks. 3. Slowly pull the shoulder part of the belt ...

Nissan Kicks - OM - Seats - Wheels and tires - Audio system -
© 2016-2026 Copyright www.hocivic.com

0.0077