Honda Civic manuals

Honda Civic Service Manual: Moonroof Frame/Drain Channel Slider and Cable Assembly Removal and Installation (2-door)

Honda Civic Service Manual / Body / "Roof - Fixed, Leisure" / Roof Drainage / Moonroof Frame/Drain Channel Slider and Cable Assembly Removal and Installation (2-door)

Removal

1. Battery Terminal (SRS) - Disconnection

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable and battery sensor (A) from the battery (B).

NOTE: Always disconnect the negative side first.

3.

Disconnect the positive cable (C) from the battery.

4.

Wait at least 3 minutes before starting work.

2. A-Pillar Trim Both

1.

Pull out the A-pillar trim (A) to release the clips.

2.

Put a shop towel (A) in the opening between the A-pillar trim (B) and the dashboard to prevent dropping the A-pillar clips.

3.

Disconnect the connector (A), then remove the A-pillar trim (B).

NOTE: The upper clip (C) will stay in the body.

4.

Remove the upper clip (A) from the body.

5.

Repeat on the opposite side.

3. Both Front Seat Belt Lower Anchor Bolts

Driver's side

Passenger's side

1.

Remove the lower anchor cap (A).

2.

Remove the lower anchor bolt (B).

4. Front Door Opening Seal As Needed Both

1.

Remove front door opening seal (A) as needed.

2.

Repeat on the opposite side.

5. Front Door Sill Trim - 2-Door

1.

Remove the cap (A).

2.

Remove the opener lock cylinder (B).

3.

Remove the screw (A).

4.

Remove the front door sill trim (A).

6. Front Door Sill Trim - 2-Door

1.

Remove the front door sill trim (A).

7. Both Kick Panels

Driver's side

Passenger's side

1.

Pull out both front door opening seals (A) as needed.

2.

Remove both kick panels (B).

8. Rear Seat Cushion

1.

Remove the bolt (A) securing the rear seat cushion (B).

2.

While pushing down the rear seat cushion (A), pull the seat hook handles (B) to release the hooks (C).

3.

Remove the rear seat cushion.

9. Rear Seat-Back - Fold Down

1.

Remove the rear seat-back (A).

10. Right Rear Seat-Back - Split Fold Down

1.

Remove the right rear seat-back (A).

11. Center Pivot Bracket - Split Fold Down

1.

Remove the center pivot bracket (A).

2.

If necessary, remove the bushing (B).

12. Left Rear Seat-Back - Split Fold Down

1.

Remove the bolt (A) securing the left rear seat-back (B).

2.

Extend the center seat belt (A), then remove the left rear seat-back (B).

13. Both Quarter Pillar Trims

1.

Remove the cap (A) and the clip (B).

2.

The left side is shown; repeat on the right side.

3.

Lower the coat hanger hook (A), then remove the screw (B).

4.

The left side is shown; repeat on the right side.

5.

Pull out the quarter pillar trim (A) to release the clips.

6.

Remove the quarter pillar trim.

NOTE: The rear clip (B) will stay in the body.

7.

The left side is shown; repeat on the right side.

8.

Remove the rear clip (A).

9.

The left side is shown; repeat on the right side.

14. Rear Shelf Trim

1.

Fold down the seat-back(s).

2.

From the trunk compartment, disconnect the connector (A).

3.

From the trunk compartment, detach the clips (A).

4.

Release the hooks (A).

5.

Pull out both rear seat belts (A) and the rear center seat belt (B) through the slits in the rear shelf trim (C), then remove the rear shelf trim.

15. Both Rear Side Trim Panels

1.

Remove the rear side trim panel (A).

2.

The left side is shown; repeat on the right side.

16. Both B-Pillar Upper Trims

1.

Remove the B-pillar upper trim (A).

2.

The left side is shown; repeat on the right side.

3.

Pass the front seat belt lower anchor (A) out through the hole in the B-pillar upper trim (B), then remove the trim.

4.

The left side is shown; repeat on the right side.

17. Grab Handles for One Vehicle

1.

Lower the grab handle (A).

2.

Insert a small flat-tip screwdriver into the notch.

3.

Pull on the small flat-tip screwdriver with the appropriate trim tool (A), then remove the cap (B).

4.

Remove the grab handle (A).

5.

Remove the clips (A).

18. Both Sunvisors

1.

Push the hook (A) with a flat-tip screwdriver through the hole in the front side of the bracket cover (B).

NOTE: Make sure the hook is unlocked.

2.

While pushing in the hook (A) with a flat-tip screwdriver, release the sunvisor (B) from the holder (C), and rotate the sunvisor backward 45 °.

NOTE: Make sure the hook slides into the bracket cover as you rotate the sunvisor.

3.

Disconnect the connector (A), then remove the sunvisor (B).

NOTE: If the sunvisor cannot be removed, the hook has not rotated into the bracket cover. Repeat step 2 to rotate the hook.

4.

If necessary, turn the sunvisor holder (A) 45 ° counterclockwise, then remove it from the holder grommet (B).

5.

If necessary, remove the holder grommet (A).

19. Front Individual Map Light (without moonroof)

1.

Turn the front individual map light switch OFF.

2.

Carefully pry off the lenses (A) with a flat-tip screwdriver.

3.

Disconnect the connector.

4.

Remove the front individual map light (B).

20. Ceiling Light

llghr

1.

Turn the ceiling light switch OFF.

2.

Carefully pry off the lens (A).

3.

Remove the ceiling light (B).

4.

Disconnect the connector.

21. Headliner - 2-Door

1.

Without moonroof: From the driver's A-pillar, detach the harness clips (A).

2.

Without moonroof: From under the driver's dash, disconnect the connector (A), and detach the harness clips (B).

3.

From the passenger's A-pillar, disconnect the connector (A), and detach the harness clips (B).

4.

For some models: Release the glove box stops (A) on each side of the dashboard.

5.

For some models: From the glove box opening, disconnect the connector (A), and detach the harness clip (B).

6.

From the right quarter pillar, disconnect the connector (A), and detach the harness clip (B).

7.

With navigation: From the left quarter pillar, remove the cover (A), and disconnect the terminal (B), then remove the bolt (C).

Without moonroof

With moonroof

8.

Slide the front seat all the way back, and recline the seat-back fully.

9.

With the help of an assistant, lower the headliner (A).

10.

With the help of an assistant, remove the headliner (A) through the passenger's door opening.

NOTE: Do not bend the headliner. Bending the headliner will crease and damage it.

22. Moonroof Link Cover Both

1.

Remove the lid (A).

2.

Remove the moonroof link cover (B).

3.

Repeat on the opposite side.

23. Moonroof Glass

1.

Remove the bolts (A).

2.

Repeat on the opposite side.

3.

Remove the moonroof glass (A).

24. Moonroof Deflector

1.

Open the glass fully.

2.

Remove both moonroof wind deflector links (A).

3.

Remove the moonroof wind deflector (A).

4.

Remove both moonroof wind deflector arm bases (A).

25. Drain Channel

1.

Tilt up the glass bracket (A).

2.

Disconnect the drain channel rods (B).

3.

Slide the drain channel (A) forward.

4.

Remove the drain channel (A).

26. Moonroof Sunshade

1.

Remove both moonroof sunshade slider spacers (A).

2.

Remove both moonroof sunshade rear hooks (A).

3.

Remove the moonroof sunshade (A).

4.

Remove both front moonroof sunshade base sliders (A) and both rear moonroof sunshade base sliders (B).

27. Moonroof Motor

1.

Remove the moonroof motor (A).

28. Moonroof Frame (2-door)

1.

Disconnect the moonroof front drain tubes (A) and the moonroof rear drain tubes (B).

2.

Remove the harness clips (A).

3.

Remove the roof wire harness (B).

4.

Remove the moonroof frame assembly (A).

29. Moonroof Cable

1.

Remove the moonroof cable assembly (A).

30. Moonroof Drain Channel Slider

1.

Remove the screw (A) and the bolt (B).

2.

Repeat on the opposite side.

3.

Turn both cable tube side brackets (A).

4.

Slide both glass brackets (B).

5.

Slide the moonroof cable assembly (C) half-way back.

6.

Remove both moonroof drain channel sliders (A).

Installation

1. Moonroof Drain Channel Slider

1.

Apply multipurpose grease to the glass bracket (A) and the guide rail area of the frame (B) indicated by the arrows.

2.

Install both moonroof drain channel sliders (A).

3.

Install the moonroof cable assembly (A).

4.

Install both glass brackets (B).

5.

Install both cable tube side brackets (C).

6.

Install the screws (A) and the bolt (B).

7.

Repeat on the opposite side.

2. Moonroof Cable

1.

Install the moonroof cable assembly (A).

3. Moonroof Frame

1.

Install the moonroof frame assembly (A).

2.

Install the harness clips (A).

3.

Install the roof wire harness (B).

4.

Connect the moonroof front drain tubes (A) and the moonroof rear drain tubes (B).

4. Moonroof Motor

1.

Install the moonroof motor (A).

5. Moonroof Sunshade

1.

Install both front moonroof sunshade base sliders (A) and both rear moonroof sunshade base sliders (B).

2.

Install the moonroof sunshade (A).

3.

Install both moonroof sunshade rear hooks (A).

4.

Install both moonroof sunshade slider spacers (A).

6. Drain Channel

1.

Install the drain channel (A).

2.

Slide the drain channel (A) rearward.

3.

Connect the drain channel rods (A).

4.

Tilt down the glass bracket (B).

7. Moonroof Deflector

1.

Install both moonroof wind deflector arm bases (A).

2.

Install the moonroof wind deflector (A).

3.

Install both moonroof wind deflector links (A).

8. Moonroof Glass

1.

Install the moonroof glass (A).

2.

Install the bolts.

3.

Repeat on the opposite side.

9. Moonroof Link Cover Both

1.

Install the moonroof link cover (A).

2.

Install the lid (B).

3.

Repeat on the opposite side.

10. Headliner - 2-Door

1.

With the help of an assistant, take the headliner (A) in through the passenger's door opening.

NOTE: Do not bend the headliner. Bending the headliner will crease and damage it.

Without moonroof

With moonroof

2.

With the help of an assistant, install the headliner (A).

asnwu

3.

With navigation: At the left quarter pillar, connect the terminal (A), and install the bolt (B), then install the cover (C).

4.

At the right quarter pillar, connect the connector (A), and install the harness clip (B).

5.

For some models: At the glove box opening, connect the connector (A), and install the harness clip (B).

6.

For some models: Install the glove box stops (A) on each side of the dashboard.

7.

At the passenger's A-pillar, connect the connector (A), and install the harness clips (B).

8.

Without moonroof: At under the driver's dash, connect the connector (A), and install the harness clips (B).

9.

Without moonroof: At the driver's A-pillar, install the harness clips (A).

11. Ceiling Light

cullingllghr

1.

Connect the connector.

2.

Install the ceiling light (A).

3.

Carefully install the lens (B).

12. Front Individual Map Light (without moonroof)

1.

Connect the connector.

2.

Install the front individual map light (A).

3.

Carefully install the lenses (B).

13. Both Sunvisors

1.

Install the holder (A) into the holder grommet (B) by turning it 45 ° clockwise.

2.

Install the holder and holder grommet as an assembly into the body by pushing it until the hooks snap into place securely.

3.

Connect the connector (A), and install the sunvisor (B).

4.

While holding the bracket cover (A), rotate the sunvisor (B) forward until the hook (C) snaps into place.

5.

Gently pull down on the sunvisor to make sure it is properly secured in the body.

6.

Rotate the sunvisor into the holder (D).

14. Grab Handles for One Vehicle

1.

Install the clips (A) on the grab handle (B).

2.

Install the caps (C) fully into the clips.

3.

Position the grab handle (A) on the grab handle bracket (B).

4.

Push on the grab handle until the clips (C) snap into place securely.

15. Both B-Pillar Upper Trims

1.

Pass the front seat belt lower anchor (A) in through the hole in the B-pillar upper trim (B).

2.

The left side is shown; repeat on the right side.

3.

Install the B-pillar upper trim (A).

4.

The left side is shown; repeat on the right side.

16. Both Rear Side Trim Panels

1.

Install the rear side trim panel (A).

2.

The left side is shown; repeat on the right side.

17. Rear Shelf Trim

1.

Slip the rear seat belts (A) and the rear center seat belt (B) through the slits in the rear shelf trim (C).

2.

Install the hooks (A).

3.

Install the clips (A).

4.

From the trunk compartment, connect the connector (A).

5.

Raise the seat-back(s).

18. Both Quarter Pillar Trims

1.

Install the new rear clip (A) to the quarter pillar trim (B).

2.

Fit the clips into the holes in the quarter pillar.

3.

Lightly push the quarter pillar trim (A) into place, then install the trim.

NOTE:

Make sure the side curtain airbag is not tucked under the clips or the ribs.

Do not push too hard on the quarter pillar trim. If you push too hard, the clip will be damaged, and it will not hold the trim properly.

Gently tug on the quarter pillar trim to verify that all clips are securely fastened.

4.

Install the screw (A).

5.

Install the clip (A) and the cap (B).

19. Left Rear Seat-Back - Split Fold Down

1.

Extend the center seat belt (A), then install the pivot shaft (B) to the center pivot bracket (C).

2.

Install the left rear seat-back (A).

20. Center Pivot Bracket - Split Fold Down

1.

If necessary, install the bushing (A).

2.

Install the center pivot bracket (B).

21. Right Rear Seat-Back - Split Fold Down

1.

Install the right rear seat-back (A).

22. Rear Seat-Back - Fold Down

1.

Install the rear seat-back (A).

23. Rear Seat Cushion

1.

Install the hooks (A) to the rear seat cushion clips (B).

2.

Install the bolt (A) securing the rear seat cushion (B).

24. Both Kick Panels

Driver's side

Passenger's side

1.

Install both kick panels (A).

2.

Install both front door opening seals (B) as needed.

25. Front Door Sill Trim - 2-Door

1.

Install the front door sill trim (A).

26. Front Door Sill Trim - 2-Door

1.

Install the front door sill trim (A).

2.

Install the screw (A).

3.

Install the opener lock cylinder (A).

4.

Install the cap (B).

27. Front Door Opening Seal as Needed Both

1.

Install front door opening seal (A).

2.

Repeat on the opposite side.

28. Both Front Seat Belt Lower Anchor Bolts

Driver's side

Passenger's side

@@@

1.

Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.

NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

Driver's side

7m2nmn:mm

Passenger's side

unr:2inm,

2.

Install the lower anchor bolt (A).

3.

Install the lower anchor cap (B).

29. A-Pillar Trim Both

1.

Carefully install the new upper clip (A) to the A-pillar trim (B).

2.

Connect the connector (A).

3.

Fit the clips into the holes in the A-pillar.

4.

Lightly push the A-pillar trim (B) into place, then install the trim.

NOTE:

Make sure the side curtain airbag is not tucked under the clips or the trim ribs.

Do not push too hard on the A-pillar trim. If you push too hard, the clip will be damaged, and it will not hold the trim properly.

Gently tug on the A-pillar trim to verify that all clips are securely fastened.

5.

Repeat on the opposite side.

30. Headliner/Pillar Trim Overlap - Check

tms

Checking and Adjusting the Headliner/Pillar Trim Overlap

To prevent the side curtain airbag from deploying and damaging the pillar trim (A-pillar trim, B-pillar trim, C-pillar trim, quarter pillar trim), the overlap between the headliner and pillar trim must be less than 8 mm (0.31 in). To check the overlap, do this:

1.

Install the headliner (A) and the pillar trim (B).

2.

Apply masking tape (A) to the headliner (B) to mark the upper edge of the pillar trim (C).

sun:orlessthan

3.

Remove the pillar trim, and measure the headliner overlap.

If the overlap is less than 8 mm (0.31 in), remove the tape, and install the pillar trim.

If the overlap is more than 8 mm (0.31 in), go to step 4.

slmws

4.

Carefully trim the headliner with a utility knife, reducing the overlap to less than 8 mm (0.31 in).

5.

Remove the tape, and install the pillar trim.

31. Battery Terminal (SRS) - Reconnection

(o.2ao.sam.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery (B).

NOTE: Always connect the positive side first.

3.

Connect the negative cable and battery sensor (C) to the battery.

4.

Apply multipurpose grease to the terminals to prevent corrosion.

Moonroof Drain Tube Removal and Installation (4-door)
Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition switch is in LOCK (0). ...

Moonroof Frame/Drain Channel Slider and Cable Assembly Removal and Installation (4-door)
Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition switch is in LOCK (0). ...

See also:

Honda Civic Owners Manual. Operating Apple CarPlay with Siri Eyes Free
Press and hold the talk button to activate Siri Eyes Free. Operating Apple CarPlay with Siri Eyes Free Below are examples of questions and commands for Siri Eyes Free. What movies are playing today’ Call dad at work. What song is this’ How’s the weather tomorrow’ Read my l ...

© 2016-2018 Copyright www.hocivic.com