Honda Civic manuals

Honda Civic Service Manual: Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Removal and Installation (4-door except Natural Gas models)

Honda Civic Service Manual / Body / Doors and Enclosures / Trunklid/Tailgate/Cargo Doors / Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Removal and Installation (4-door except Natural Gas models)

823160

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Front Door Sill Trim - 4-Door

1.

Remove the cap (A) from the front door sill trim (B).

2.

Remove the opener lock cylinder (C).

3.

Remove the screw (A).

4.

Remove the front door sill trim (A).

2. Trunk Lid Opener/Fuel Fill Door Opener

1.

Loosen the opener mounting rear bolt (A).

2.

Remove the opener mounting front bolt (B), then remove the trunk lid opener/fuel fill door opener (C).

3.

Disconnect the trunk lid opener cable/fuel fill door opener cable (A) from the opener.

3. Rear Door Sill Trim

1.

While pushing down on the rear seat cushion (A), pull the seat hook handle (B) to release the hook (C).

2.

While pulling up the seat cushion, remove the rear door sill trim (D).

4. Front and Rear Door Opening Seals as Needed

Front

Rear

1.

Remove the front door opening seal (A) and the rear door opening seal (B) as needed.

5. B-Pillar Lower Trim

1.

Slide the front seat forward fully.

2.

13-14 Models (driver's side): Remove the B-pillar lower cover (A).

12 Model

13-14 Models

3.

Remove the B-pillar lower trim (A).

6. Rear Seat Cushion

1.

Remove the bolt (A) securing the rear seat cushion (B).

2.

While pushing down the rear seat cushion (A), pull the seat hook handles (B) to release the hooks (C).

3.

Remove the rear seat cushion.

7. Both Rear Seat Side Bolsters

1.

Remove the bolt (A) securing the rear seat side bolster (B).

2.

The left side is shown; repeat on the right side.

3.

Remove the rear seat side bolster (A).

4.

The left side is shown; repeat on the right side.

8. Trunk Floor Cover

1.

Fold down the seat-back(s).

2.

Remove the front area of the trunk floor cover (A).

3.

Remove the trunk floor cover (A).

9. Trunk Lid Weatherstrip as Needed

1.

Remove the trunk lid weatherstrip (A) as needed.

10. Trunk Rear Trim Panel

1.

Remove the trunk rear trim panel (A).

11. Trunk Side Trim Panel

1.

Remove the trunk side trim panel (A).

12. Trunk Lid Trim Panel

1.

For some models: Remove the trunk lid trim panel (A).

13. Trunk Lid Latch

1.

Remove the latch cover (A).

2.

Remove the trunk lid latch (B).

3.

With trunk lid lock cylinder: Disconnect the cylinder rod (C).

4.

Disconnect the trunk lid opener cable (A).

14. Vehicle Lift

1.

Raise the vehicle on a lift, and make sure it is securely supported.

15. Rear Wheel

1.

Remove the rear wheel.

16. Fuel Pipe Protector

1.

Remove the fuel pipe protector (A).

17. Fuel Cap Adapter

1.

Remove the fuel cap (A).

2.

Remove the screw (B).

3.

Remove the bolts (A).

4.

Lower the fuel filler pipe (B), then remove it from the fuel cap adapter (C).

5.

Turn the fuel cap adapter (A), then remove it.

18. Trunk Lid/Fuel Fill Door Opener Cable

1.

Remove the clip (A) and the cushion tapes (B) securing the trunk lid opener cable/fuel fill door opener cable (C).

2.

Remove the grommet (A) from the body.

3.

Remove the grommet (A) from the fuel fill door latch (B).

4.

Remove the fuel fill door opener cable (C) from inside the body.

5.

Detach the clips (A), and release the trunk lid opener cable/fuel fill door opener cable (B) from the clips (C), then remove the cable from the vehicle.

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Trunk Lid/Fuel Fill Door Opener Cable

1.

Install the trunk lid opener cable/fuel fill door opener cable (A) to the clips (B), and install the clips (C) securing the cable.

NOTE: Align the marks (D) with the clips as shown.

2.

Install the grommet (A) to the fuel fill door latch (B).

3.

Install the grommet (A) to the body.

4.

Install the cushion tapes (A) and the clip (B) securing the trunk lid opener cable/fuel fill door opener cable (C).

NOTE: Align the marks (D) with the cushion tapes and the clip as shown.

2. Fuel Cap Adapter

1.

Install the fuel cap adapter (A) into place.

2.

Raise the fuel filler pipe (A), and install it to the fuel cap adapter (B).

3.

Install the bolts (C).

4.

Install the screw (A).

5.

Install the fuel cap (B).

3. Fuel Pipe Protector

1.

Install the fuel pipe protector (A).

4. Rear Wheel

15mmumum

1.

Install the rear wheel.

NOTE: Before installing the wheel, clean the mating surfaces between the brake disc or the brake drum and the inside of the wheel.

5. Trunk Lid Latch

NOTE: Fix the original position of the outer end of the cable (A) on the trunk lid latch securely. And check the trunk lid latch operation: Make sure the trunk lid latch unlocks when pulling the trunk lid opener/fuel fill door opener. If necessary, adjust the position of the cable end.

1.

Connect the trunk lid opener cable (A).

2.

With trunk lid lock cylinder: Connect the cylinder rod (A).

3.

Install the trunk lid latch (B).

4.

Install the latch cover (C).

6. Trunk Lid Trim Panel

1.

For some models: Install the trunk lid trim panel (A).

7. Trunk Side Trim Panel

1.

Install the trunk side trim panel (A).

8. Trunk Rear Trim Panel

1.

Install the trunk rear trim panel (A).

9. Trunk Lid Weatherstrip as Needed

1.

Install the trunk lid weatherstrip (A).

10. Trunk Floor Cover

1.

Install the trunk floor cover (A).

2.

Install the front area of the trunk floor cover (A).

3.

Raise the seat-back(s).

11. Both Rear Seat Side Bolsters

1.

Install the rear seat side bolster (A).

2.

The left side is shown; repeat on the right side.

mmmmlnss

3.

Install the bolt (A) securing the rear seat side bolster (B).

4.

The left side is shown; repeat on the right side.

12. Rear Seat Cushion

1.

Install the hooks (A) to the rear seat cushion clips (B).

2.

Install the bolt (A) securing the rear seat cushion (B).

13. B-Pillar Lower Trim

12 Model

13-14 Models

1.

Install the B-pillar lower trim (A).

2.

13-14 Models (driver's side): Install the B-pillar lower cover (A).

14. Front and Rear Door Opening Seals as Needed

Front

Rear

1.

Install the front door opening seal (A) and the rear door opening seal (B).

15. Rear Door Sill Trim

1.

While pulling up the rear seat cushion (A), install the rear door sill trim (B).

2.

Push down the seat cushion, then install the hook (C) to the rear seat cushion clip (D).

16. Trunk Lid Opener/Fuel Fill Door Opener

1.

Connect the trunk lid opener cable/fuel fill door opener cable (A) to the opener.

2.

Install the opener mounting rear bolt (A) temporarily.

3.

Install the opener mounting front bolt (B).

4.

Install the front door sill trim (A).

5.

Install the screw (A).

6.

Tighten the opener mounting rear bolt (B).

7.

Install the opener lock cylinder (A).

8.

Install the cap (B) to the front door sill trim (C).

Trunk Lid Latch Removal and Installation
8171B6 Removal 1. Trunk Lid Trim Panel 1. For some models: ...

Trunk Lid Opener/Fuel Fill Door Opener Removal and Installation
849110 Removal 1. Front Door Sill Trim - 4-Door 1. Remo ...

See also:

Honda Civic Owners Manual. Selecting a Mail Account
If a paired phone has text or mail message accounts, you can select one of them to be active and receive notifications.  Go to the phone settings screen. Select the Text/Email tab, then Select Account.  A pop-up menu appears on the screen.  Select Text Messa ...

© 2016-2024 Copyright www.hocivic.com

0.0093