Honda Civic Service Manual: Rear Speaker Removal, Installation, and Test (2-door)
013100 LEFT REAR
0131A8 RIGHT REAR
Removal
|
NOTE: SRS components are located in this area. Review the SRS
component locations and the precautions and procedures before doing
repairs or service.
|
| 1. |
Both Quarter Pillar Trims |
|
|
|
1.
|
Remove the cap (A) and the clip (B).
|
|
2.
|
The left side is shown; repeat on the right side.
|
|
|
|
|
3.
|
Lower the coat hanger hook (A), then remove the screw
(B).
|
|
4.
|
The left side is shown; repeat on the right side.
|
|
|
|
|
5.
|
Pull out the quarter pillar trim (A) to release the clips.
|
|
6.
|
Remove the quarter pillar trim.
|
|
NOTE: The rear clip (B) will stay in the body.
|
|
7.
|
The left side is shown; repeat on the right side.
|
|
|
|
|
8.
|
Remove the rear clip (A).
|
|
9.
|
The left side is shown; repeat on the right side.
|
|
|
|
|
1.
|
Fold down the seat-back(s).
|
|
2.
|
From the trunk compartment, disconnect the connector
(A).
|
|
|
|
|
3.
|
From the trunk compartment, detach the clips (A).
|
|
|
|
|
4.
|
Release the hooks (A).
|
|
|
|
|
5.
|
Pull out both rear seat belts (A) and the rear center
seat belt (B) through the slits in the rear shelf trim (C),
then remove the rear shelf trim.
|
|
|
|
|
1.
|
Remove the screw. Remove the rear speaker (A) by tilting
it forward to release the clips (B).
|
|
2.
|
Disconnect the connector.
|
|
Test
|
|
|
1.
|
Measure the resistance between terminals No. 1 and No.
2. There should be about 4 ?.
|
|
2.
|
If the resistance is not as specified, replace the rear
speaker (A).
|
|
Installation
|
NOTE: SRS components are located in this area. Review the SRS
component locations and the precautions and procedures before doing
repairs or service.
|
|
 mmmmwzzm.mwn
|
|
1.
|
Connect the connector.
|
|
2.
|
Install the rear speaker (A).
|
|
|
|
|
1.
|
Slip the rear seat belts (A) and the rear center seat
belt (B) through the slits in the rear shelf trim (C).
|
|
|
|
|
2.
|
Install the hooks (A).
|
|
|
|
|
3.
|
Install the clips (A).
|
|
|
|
|
4.
|
From the trunk compartment, connect the connector (A).
|
|
5.
|
Raise the seat-back(s).
|
|
| 3. |
Both Quarter Pillar Trims |
|
|
|
1.
|
Install the new rear clip (A) to the quarter pillar trim
(B).
|
|
|
|
|
2.
|
Fit the clips into the holes in the quarter pillar.
|
|
3.
|
Lightly push the quarter pillar trim (A) into place,
then install the trim.
|
|
NOTE:
|
|
|
Make sure the side curtain airbag is
not tucked under the clips or the ribs.
|
|
|
|
Do not push too hard on the quarter pillar
trim. If you push too hard, the clip will
be damaged, and it will not hold the trim
properly.
|
|
|
|
Gently tug on the quarter pillar trim
to verify that all clips are securely fastened.
|
|
|
|
|
|
|
4.
|
Install the screw (A).
|
|
|
|
|
5.
|
Install the clip (A) and the cap (B).
|
|
Removal
1.
Right Rear Seat-Back - Split Fold Down
1.
Remove the ...
832120
Removal
1.
Rear Seat Cushion
1.
Remove the bolt (A) ...
Rear Seat-Back Removal and Installation - Split Fold Down type (4-door)
Rear Window Removal and Installation (4-door except Natural Gas models)