Honda Civic manuals

Honda Civic Service Manual: M/T Differential Thrust Clearance Adjustment (K24Z7)

Honda Civic Service Manual / Powertrain / Driveline / Differentials / M/T Differential Thrust Clearance Adjustment (K24Z7)

Disassembly

1. M/T Change Lever Assembly


1.

Remove the interlock bolt (A).


2.

Remove any old liquid gasket from the interlock bolt.


3.

Remove the change lever assembly (B).


4.

Remove the 8 x 14 mm dowel pins (C).


2. Back-Up Light Switch


1.

Remove the back-up light switch (A).


2.

Remove any old liquid gasket.


3. Output Shaft (Countershaft) Speed Sensor

1.

Remove the output shaft (countershaft) speed sensor (A), the plain washer (B), and the O-ring (C).


4. Transmission Housing

1.

Remove the detent bolts (A), the 12 mm sealing washers (B), the detent ball springs (C), and the steel balls (D).


2.

Remove the 10 mm flange bolt (A) and the sealing washer (B).


3.

Loosen the 8 mm flange bolts in a crisscross pattern in several steps, then remove them with transmission hanger A, transmission hanger B, and the harness bracket (C).



4.

Remove the 32 mm sealing cap (A).


5.

While expanding the 72 mm snap ring (B) on the countershaft ball bearing with snap ring pliers, lift the transmission housing (C).


6.

Release the snap ring pliers, and remove the transmission housing.


7.

Remove the 14 x 20 mm dowel pins (D).


5. Reverse Shift Fork

1.

Remove the reverse shift fork (A).


6. Baffle Plate

1.

Remove the baffle plate (A).


7. Reverse Idler Gear

1.

Remove the reverse idler gear (A) and the reverse idler gear shaft (B).


8. M/T Mainshaft and Countershaft and Shift Fork Assembly


1.

Apply a thin layer of tape to the mainshaft splines to protect the seal.


NOTE: Do not apply too much tape as it will damage the oil seal.


2.

Remove the mainshaft assembly (A) and the countershaft assembly (B) with the shift fork assembly (C) from the clutch housing (D).


3.

Remove the 28 mm washer (E).


4.

Remove the 28 mm spring washer (F).


9. Differential Assembly


1.

Remove the differential assembly (A).


2.

Remove the magnet (B).


Adjustment

1. M/T Differential Thrust Clearance Adjustment

1.

Remove the oil seal (A).


NOTE: Be careful not to damage the transmission housing while removing the oil seal.


2.

If you removed the 80 mm shim (A) from the transmission housing, reinstall the same sized shim.


3.

Install the differential assembly (A).


4.

Install the transmission housing onto the clutch housing.


NOTE: Tighten the 8 mm flange bolts in a crisscross pattern in several steps.


Specified Torque:

8 x 1.25 mm
27 N·m (2.8 kgf·m, 20 lbf·ft)


5.

Use the 40 mm I.D. driver handle to bottom the differential assembly in the clutch housing.



6.

Measure the clearance between 80 mm shim and the bearing outer race in the transmission housing.


Standard:

0-0.10 mm
(0-0.003 in)


7.

If the clearance exceeds the standard, select a new 80 mm shim from the following table. If the clearance measured in step 6 is within the standard, go to step 10.


80 mm Shim

Type

Thickness

A

1.00 mm (0.0394 in)

B

1.10 mm (0.0433 in)

C

1.20 mm (0.0472 in)

D

1.30 mm (0.0512 in)

E

1.40 mm (0.0551 in)

F

1.50 mm (0.0591 in)

G

1.60 mm (0.0630 in)

H

1.70 mm (0.0669 in)

J

1.80 mm (0.0709 in)

K

1.05 mm (0.0413 in)

L

1.15 mm (0.0453 in)

M

1.25 mm (0.0492 in)

N

1.35 mm (0.0531 in)

P

1.45 mm (0.0571 in)

Q

1.55 mm (0.0610 in)

R

1.65 mm (0.0650 in)

S

1.75 mm (0.0689 in)


8.

Remove the transmission housing.


9.

Replace the thrust shim with the correct one selected in step 7, then recheck the clearance.


10.

Install a new oil seal flush with the transmission housing using the 64 mm oil seal driver.


Reassembly

1. Differential Assembly


1.

Install the magnet (A).


NOTE: Clean the magnet any time the transmission is disassembled.


2.

Install the differential assembly (B).


2. M/T Mainshaft and Countershaft and Shift Fork Assembly


1.

Install the 28 mm spring washer (A).


NOTE: Be sure to install the spring washer in the direction shown.


2.

Install the 28 mm washer (B).


3.

Apply a thin layer of tape to the mainshaft splines (C) to protect the seal.


NOTE: Do not apply too much tape as it will damage the oil seal.


4.

Install the mainshaft assembly (D) and the countershaft assembly (E) with the shift fork assembly (F), as an assembly.


3. Reverse Idler Gear

1.

Install the reverse idler gear (A) and reverse idler gear shaft (B) by aligning the mark (C) on the clutch housing with the reverse idler gear shaft hole (D).


4. Baffle Plate

1.

Install the baffle plate (A).


5. Reverse Shift Fork

mmlbf!

1.

Install the reverse shift fork (A).


6. Transmission Housing


1.

Clean any dirt or oil from the mating surface of the transmission housing and the clutch housing.


2.

Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the clutch housing mating surface of the transmission housing. Install the component within 5 minutes of applying the liquid gasket.


NOTE:

If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.

If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.



3.

Install the 14 x 20 mm dowel pins (A).


4.

Place the transmission housing on the clutch housing, making sure to line up the shafts.


5.

While expanding the 72 mm snap ring (B) on the countershaft ball bearing using snap ring pliers, push the transmission housing down to start the countershaft ball bearing through the snap ring.


6.

Release the pliers, and push down the housing until it bottoms out and the snap ring snaps in place in the countershaft ball bearing snap ring groove.


NOTE: Install the 32 mm sealing cap (C) after setting in the 72 mm snap ring.



7.

Make sure the 72 mm snap ring (A) is securely seated in the groove of the countershaft bearing.


Dimension as installed: 3.3-6.0 mm (0.130-0.236 in)


8.

Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the threads of the 32 mm sealing cap. Install the component within 5 minutes of applying the liquid gasket.


NOTE:

If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.

If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.


9.

Install the 8 mm flange bolts finger-tight with transmission hanger A, transmission hanger B, and the harness bracket (C).


10.

Tighten the 8 mm flange bolts in a crisscross pattern in several steps.


Specified Torque:

8 x 1.25 mm
27 N·m (2.8 kgf·m, 20 lbf·ft)


11.

Install the 10 mm flange bolt (A) with new sealing washer (B).


12.

Install the steel balls, the detent ball springs, and the detent bolts (A) with new 12 mm sealing washers (B).


7. Output Shaft (Countershaft) Speed Sensor


1.

Apply MTF to a new O-ring (A).


2.

Install the output shaft (countershaft) speed sensor (B) with the O-ring and the plain washer (C).


8. Back-Up Light Switch


1.

Apply liquid gasket (P/N 08717-0004, 08718-0001, 08718-0012, 08718-0003, 08718-0004, or 08718-0009) to the threads of the back-up light switch (A).


2.

Install the back-up light switch.


9. M/T Change Lever Assembly

iukn


1.

Clean any dirt or oil from the mating surface of the change lever assembly and the transmission housing.


2.

Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the transmission housing mating surface of the change lever assembly. Install the component within 5 minutes of applying the liquid gasket.


NOTE:

If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes.

If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.



3.

Install the 8 x 14 mm dowel pins (A).


4.

Install the change lever assembly (B).


5.

Apply liquid gasket (P/N 08717-0004, 08718-0001, 08718-0012, 08718-0003, 08718-0004, or 08718-0009) to the threads of the interlock bolt (C).


6.

Install the interlock bolt.


Left M/T Differential Oil Seal Replacement (R18Z1 M/T)
2191F4 LEFT 1. Vehicle Lift 1. Raise the vehicle on a lift, and make sure it is securely supported. ...

Right A/T Differential Oil Seal Replacement (A/T)
2191M0 RIGHT 1. Vehicle Lift 1. Raise the vehicle on a lift, and make sure it is securely supported. ...

See also:

Honda Civic Owners Manual. VSA Operation
When VSA activates, you may notice that the engine does not respond to the accelerator. You may also notice some noise from the hydraulic system. You will also see the indicator blink. Vehicle Stability Assist (VSA), aka Electronic Stability Control (ESC), System VSA may ...

© 2016-2024 Copyright www.hocivic.com

0.0072