Honda Civic manuals

Honda Civic Service Manual: Front Passenger's Seat-Back Heater Removal and Installation ('13-'14)

Honda Civic Service Manual / Body / Seating / Front Passenger's Seat-Back Heater Removal and Installation ('13-'14)

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.
1. Battery Terminal (SRS) - Disconnection

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable with the battery sensor (A) from the battery.

NOTE:

Always disconnect the negative side first.

To protect the battery sensor connector (B) from damage, do not hold it when removing the negative terminal.

Do not disconnect the battery sensor from the negative terminal (C).

3.

Disconnect the positive cable (D) from the battery.

4.

Wait at least 3 minutes before starting work.
2. Front Seat Belt Lower Anchor - Passenger's Side

2-door

1.

Remove the lower anchor bolt (A).

4-door

1.

Remove the anchor cover (A).

2.

Remove the lower anchor bolt (A).
3. Head Restraint - Passenger's Side

1.

Remove the head restraint (A).
4. Front Seat - Passenger's Side

2-door

4-door

1.

Remove both seat track end covers (A).

2.

Remove the seat mounting front bolts (A).

3.

Remove the seat mounting rear bolts (A).

4.

Disconnect the connectors (A).
5. Front Seat-Back as Needed - Passenger's Side

2-door

4-door

1.

Release the strap(s) (A).

2-door

4-door

2.

Remove the connectors (A).

3.

Detach the harness clips (B).

4.

Release the holders (C).

5.

Unzip the seat-back cover (A).

6.

Release the hook strip (B).

7.

Release the hook strips (A).

8.

Detach the harness clips (A).

9.

Pull out the harness (B).

10.

Release airbag attachment wires A and B.

11.

For some models: Remove the cover (A).

12.

For some models: Disconnect the connectors (A).

13.

Release the hooks (A).

14.

Detach the harness clips (B).
6. Head Restraint Guide - Passenger's Side

1.

Remove the head restraint guides (A).
7. Front Seat-Back Cover/Pad - Passenger's Side

1.

Remove the seat-back cover/pad (A).
8. Front Seat-Back Cover - Passenger's Side

Except Si (Fabric)

Except Si (Leather)

Si

1.

Remove the upholstery rings (A).

2.

Remove the seat-back cover (B).

3.

Remove the airbag attachment wires A and B.
9. Seat-Back Heater - Front Passenger's Side

1.

Remove the seat-back heater (A).

NOTE: The seat-back heater is glued to the by seat-back pad. When removing it, take care not to damage the seat-back pad.

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.
1. Seat-Back Heater - Front Passenger's Side

1.

Install the seat-back heater (A).
2. Front Seat-Back Cover - Passenger's Side

NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D).

1.

Install the airbag attachment wires A and B.

Except Si (Fabric)

Except Si (Leather)

Si

2.

Install the seat-back cover (A) with the upholstery rings (B).
3. Front Seat-Back Cover/Pad - Passenger's Side

1.

Install the seat-back cover/pad (A).
4. Head Restraint Guide - Passenger's Side

1.

Install the head restraint guides (A).
5. Front Seat-Back As Needed - Passenger's Side

1.

Install the hooks (A).

2.

Install the harness clips (B).

3.

For some models: Connect the connectors (A).

4.

For some models: Install the cover (A).

5.

Install airbag attachment wires A and B.

6.

Install the harness (A) through the hole (B).

7.

Install the harness clip (C).

8.

Install the hook strips (A).

9.

Install the hook strip (A).

10.

Zip the seat-back cover (B).

2-door

4-door

11.

Install the connector clip (A).

12.

Install the harness clip (B).

13.

Install the holders (C).

2-door

4-door

14.

Install the strap(s) (A).
6. Front Seat Assembly - Passenger's Side

1.

Connect the connectors (A).

Front side

mmu....in

Rear side

2.

Install the seat mounting bolts (A).

NOTE:

Tighten the bolts by hand first, then tighten them to specified torque.

Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten 1 and 2, then slide it forward and tighten 3 and 4.

2-door

4-door

3.

Install both seat track end covers (A).
7. Head Restraint - Passenger's Side

1.

Install the head restraint (A).
8. Front Seat Belt Lower Anchor - Passenger's Side

@@

2-door

1.

Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.

NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

7/m2onm

2.

Install the lower anchor bolt (A).

um22nmin

4-door

1.

Install the lower anchor bolt (A).

2.

Install the anchor cover (A).
9. Battery Terminal (SRS) - Reconnection

(o.2ao.sam.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery.

NOTE: Always connect the positive side first.

3.

Connect the negative cable and the battery sensor (B) to the battery.

NOTE: To protect the battery sensor connector (C) from damage, do not hold it when installing the negative terminal.

4.

Apply multipurpose grease to the terminals to prevent corrosion.
10. HDS DLC - Connection

1.

Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.

2.

Turn the ignition switch to ON (II).

3.

Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC circuit troubleshooting.
11. DTC - Clear

1.

Clear the DTC(s) by following the screen prompts on the HDS.

2.

Turn the ignition switch to LOCK (0), then wait for 10 seconds.
12. OPDS Sensor Initialization

OPDS Sensor Initialization

When you replace the front passenger's seat-back cover/pad, the SRS unit, and/or the ODS unit, initialize the OPDS sensor with the HDS.

NOTE:

Before initializing the ODS unit, make sure the battery is fully charged.

A new (uninitialized) ODS unit installed with a faulty OPDS sensor (DTC 86-1x or 86-2x) can cause DTCs 85-71 and 85-78. If the SRS has a hard DTC 86-1x or 86-2x, troubleshoot the DTCs completely before replacing the ODS unit.

Make sure all components of the front passenger's seat are correctly installed.

Make sure nothing is on the front passenger's seat, including aftermarket seat covers or mats.

Make sure there is nothing in the front passenger's seat-back pocket.

Dehumidify inside of the vehicle with A/C.

1.

Set the seat-back in a normal position.

2.

From the HDS Main Menu, select SRS, then INITIALIZATION. In the INITIALIZATION Menu, select ODS Initialization. Follow the prompts until the OPDS sensor initialization has been completed.

3.

Turn the ignition switch to LOCK (0), then wait for 10 seconds.

NOTE: If the ODS unit fails to initialize after several attempts, replace the seat-back cover/pad equipped with an OPDS sensor, and retry. If the ODS unit continues to fail to initialize, replace the ODS unit.
Driver's Seat-Back Heater Removal and Installation
859122 LEFT FRONT Removal SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. ...

Front Seat Belt Removal and Installation - Driver's Seat (2-door)
Removal 1. Battery Terminal (SRS) - Disconnection 1. Make sure the ignition switch is in LOCK (0). ...

See also:

Honda Civic Owners Manual. Automatic Intermittent Wipers
When you push the lever down to AUTO, the windshield wipers sweep once, and go into the automatic mode. The wipers operate intermittently, at low speed, or at high speed and stops in accordance with the amount of rainfall the rainfall sensor detects. AUTO sensitivity adjustment When th ...

© 2016-2022 Copyright www.hocivic.com

0.1751