Honda Civic manuals

Honda Civic Service Manual: Front Passenger's Airbag Cutoff Indicator Removal and Installation

Honda Civic Service Manual / Accessories / Storage / Front Passenger's Airbag Cutoff Indicator Removal and Installation

754104

NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Battery Terminal (SRS) - Disconnection


1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable with the battery sensor (A) from the battery.

NOTE:

Always disconnect the negative side first.

To protect the battery sensor connector (B) from damage, do not hold it when removing the negative terminal.

Do not disconnect the battery sensor from the negative terminal (C).

3.

Disconnect the positive cable (D) from the battery.

4.

Wait at least 3 minutes before starting work.

2. Driver's Outer Vent

1.

Remove the driver's outer vent (A).

2.

If necessary, remove the duct (A).

3. Dashboard Center Pocket

1.

Remove the screws (A).

2.

Remove the dashboard center pocket (A).

4. Audio Unit Assembly (Without audio panel pocket)

NOTE:

Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.

Do not work in a dusty or dirty place.

Discharge static electricity from your body before and during the work.

Do not touch the circuit board(s) with your bare hands.

Do not work with dirty hands.

Do not touch the terminal connector of the flat plate cable with your bare hands (If you have touched it, wipe it off thoroughly.).

Eject the CD before disconnecting the audio unit to prevent damaging the CD player’s load mechanism.

If you are replacing the audio unit, write down the audio presets (if possible), and enter them into the new audio unit.

1.

Remove the bolts (A).

2.

Disconnect the connectors, then pull out the audio unit assembly (A).

5. Audio Unit Assembly (With audio panel pocket)

NOTE:

Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.

Do not work in a dusty or dirty place.

Discharge static electricity from your body before and during the work.

Do not touch the circuit board(s) with your bare hands.

Do not work with dirty hands.

Do not touch the terminal connector of the flat plate cable with your bare hands (If you have touched it, wipe it off thoroughly.).

Eject the CD before disconnecting the audio unit to prevent damaging the CD player’s load mechanism.

If you are replacing the audio unit, write down the audio presets (if possible), and enter them into the new audio unit.

1.

Remove the bolts (A).

2.

Disconnect the connectors, then pull out the audio unit assembly (A).

6. Audio-Navigation Unit Assembly

NOTE:

Lay a workshop towel under the parts when working on them to protect the face panel from scratches or other damage.

Do not work in a dusty or dirty place.

Discharge static electricity from your body before and during the work.

Do not touch the circuit board(s) with your bare hands.

Do not work with dirty hands.

Do not touch the terminal connector of the flat plate cable with your bare hands (If you have touched it, wipe it off thoroughly.).

Eject the disc before removing the audio-navigation unit to prevent damaging the CD player's load mechanism.

If you are replacing the audio-navigation unit, write down the audio presets (if possible), then enter them into the new audio-navigation unit.

When the audio-navigation unit is replaced or disconnected, do the Map Matching. This part of the initialization matches the GPS coordinates with a road on the map screen. To do this part of the procedure, make sure that the navigation system displays a map, and drive the vehicle on a mapped road shown on the map screen. Do not enter a destination at this time. When the name of the current road you are driving on appears at the bottom of the screen, the entire procedure is complete.

1.

Remove the bolts (A).


2.

Disconnect the connectors, then pull out the audio-navigation unit assembly (A).

7. Driver's Dashboard Lower Cover

1.

Remove the driver's dashboard lower cover (A).

8. Dashboard Subdisplay Visor

1.

Remove the dashboard subdisplay visor (A).

9. Dashboard Meter Visor

1.

Remove the screws (A).

2.

Remove the dashboard meter visor (A).

10. Information Display Unit


1.

Remove the information display unit (A).

2.

Disconnect the connectors from the information display unit.

11. Multi-Information Display Unit


1.

Remove the multi-information display unit (A).

2.

Disconnect the connectors.

12. Front Passenger's Airbag Cutoff Indicator

1.

Remove the front passenger's airbag cutoff indicator (A).

NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Front Passenger's Airbag Cutoff Indicator

1.

Install the front passenger's airbag cutoff indicator (A).

2. Multi-Information Display Unit


1.

Connect the connectors.

2.

Install the multi-information display unit (A).

3. Information Display Unit


1.

Connect the connectors to the information display unit (A).

2.

Install the information display unit.

4. Dashboard Meter Visor

1.

Install the dashboard meter visor (A).

2.

Install the screws (A).

5. Dashboard Subdisplay Visor

1.

Install the dashboard subdisplay visor (A).

6. Driver's Dashboard Lower Cover

1.

Install the driver's dashboard lower cover (A).

7. Audio-Navigation Unit Assembly

1.

Connect the connectors, then install the audio-navigation unit (A).

NOTE: Make sure all the connectors and the antenna lead are secure.

mm3.72.7

2.

Install the bolts (A).


8. Audio Unit Assembly (With audio panel pocket)

1.

Connect the connectors, then install the audio unit assembly (A).

NOTE: Make sure all the connectors and the antenna lead are securely connected.

2.

Install the bolts (A).

9. Audio Unit Assembly (Without audio panel pocket)

1.

Connect the connectors, then install the audio unit assembly (A).

NOTE: Make sure all the connectors and the antenna lead are securely connected.

2.

Install the bolts (A).

10. Dashboard Center Pocket

1.

Install the dashboard center pocket (A).

2.

Install the screws (A).

11. Driver's Outer Vent

1.

Install the duct (A).

2.

Install the driver's outer vent (A).

12. Battery Terminal (SRS) - Reconnection

(o.2ao.sam.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery.

NOTE: Always connect the positive side first.

3.

Connect the negative cable and the battery sensor (B) to the battery.

NOTE: To protect the battery sensor connector (C) from damage, do not hold it when installing the negative terminal.

4.

Apply multipurpose grease to the terminals to prevent corrosion.

13. HDS DLC - Connection


1.

Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.

2.

Turn the ignition switch to ON (II).

3.

Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC circuit troubleshooting.

14. DTC - Clear

1.

Clear the DTC(s) by following the screen prompts on the HDS.

2.

Turn the ignition switch to LOCK (0), then wait for 10 seconds.

15. Confirm Proper SRS Operation

Turn the ignition switch to ON (II), and check that the SRS indicator comes on for about 6 seconds and then goes off.

ECON Switch Removal and Installation ('13-'14)
1. Driver's Outer Vent 1. Remove the driver's outer vent (A). ...

Information Display Unit Removal and Installation ('13)
1. Driver's Outer Vent 1. Remove the driver's outer vent (A). ...

See also:

Honda Civic Owners Manual. Customizing the Meter
You can edit, add, or delete the meter contents on the driver information interface. 1. 2. Settings 3. System 4. Configuration of Instrument Panel Customizing the Meter You can store up to three customized configurations. To select or customize a configuration, press Swap Config.. ...

© 2016-2024 Copyright www.hocivic.com

0.0264