Honda Civic manuals

Honda Civic Service Manual: Engine Oil Filter Feed Pipe Removal and Installation (Except K24Z7)

Honda Civic Service Manual / Powertrain / Engine / Engine Lubrication / Engine Oil Filter Feed Pipe Removal and Installation (Except K24Z7)

1111M6

1. Vehicle Lift

1.

Raise the vehicle on a lift, and make sure it is securely supported.


2. Oil Filter Assembly

1.

Remove the oil filter with the oil filter wrench.



2.

Inspect the filter to make sure the rubber seal is not stuck to the oil filter seating surface of the engine.


3.

Inspect the threads (A) and the rubber seal (B) on the new filter.


4.

Clean the seat on the oil pan.


5.

Apply a light coat of new engine oil to the oil filter rubber seal.


NOTE: Use only filters with a built-in bypass system.


3. Oil Filter Feed Pipe

1.

Remove the oil filter feed pipe.


1. Oil Filter Feed Pipe


1.

Install the two 22 x 1.5 mm nuts (A) onto the new oil filter feed pipe. Hold the nut with a wrench, then tighten the other nut.


2.

Torque the oil filter feed pipe to 35 N·m (3.6 kgf·m, 26 lbf·ft).


3.

Remove the nuts from the oil filter feed pipe.


2. Oil Filter Assembly

1.

Install the oil filter by hand.



2.

After the rubber seal seats, tighten the oil filter clockwise with the oil filter wrench.


Tighten:

3/4 Turn Clockwise

Tightening Torque:

12 N·m (1.2 kgf·m, 9 lbf·ft)


3.

If four numbers or marks (1 to 4 or ▼ to▼▼▼▼) are printed around the outside of the filter, use the following procedure to tighten the filter.


Spin the filter on until its seal lightly seats against the oil pan, and note which number or mark is at the bottom.

Tighten the filter by turning it clockwise three numbers or marks from the one you noted. For example, if mark▼is at the bottom when the seal is lightly seated, tighten the filter until the mark ▼▼▼▼comes around to the bottom.


Number or Mark when rubber seal is seated

1
or

2
or
▼▼

3
or
▼▼▼

4
or
▼▼▼▼

Number or Mark after tightening

4
or
▼▼▼▼

1
or

2
or
▼▼

3
or
▼▼▼


3. Warm Up The Engine Wait Few Minutes

1.

Park the vehicle on level ground, and start the engine. Hold the engine speed at 3,000 rpm with no load (in neutral (M/T model) or P or N (A/T model) ) until the radiator fan comes on, then turn off the engine, and wait more than 3 minute.


4. Engine Oil Level - Check


1.

Remove the dipstick, and wipe off the dipstick, then reinstall the dipstick.


2.

Remove the dipstick.


3.

Check the engine oil level. It should be between the upper mark (A) and the lower mark (B).


4.

If the engine oil level is near or below the lower mark check for oil leaks, and add the engine oil to bring it to the upper mark.


5. Engine Oil Filter After Install - Check

1.

Run the engine for at least 3 minutes, then check for oil leaks.


Engine Oil Filter Base Removal and Installation (K24Z7)
1111B4 1. Vehicle Lift 1. Raise the vehicle on a lift, and make sure it is securely supported. ...

Engine Oil Filter Removal and Installation (Except K24Z7)
1111B5 1. Vehicle Lift 1. Raise the vehicle on a lift, and make sure it is securely supported. ...

See also:

Honda Civic Owners Manual. Using the Smart Entry with Push Button Start System
When you carry the smart entry remote, you can lock/unlock the doors, fuel fill door, and open the trunk. You can lock/unlock the doors and fuel fill door within a radius of about 32 inches (80 cm) of the outside door handle. You can open the trunk within about 32 inches (80 cm) radius ...

© 2016-2024 Copyright www.hocivic.com

0.0265