Honda Civic Service Manual: Audio Remote/Multi-Information Display Switch Removal, Installation, and Test

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable and battery sensor (A) from the battery (B).

NOTE: Always disconnect the negative side first.

3.

Disconnect the positive cable (C) from the battery.

4.

Wait at least 3 minutes before starting work.

1.

Remove the access panel (A).

2.

Disconnect the driver's airbag inflator connector (B) on the cable reel harness.

3.

Disconnect the horn switch connector (C).

4.

Remove the TORX bolts using a TORX T30 bit.

5.

Remove the driver's airbag (A).

1.

Set the front wheels in the straight ahead position.

2.

Disconnect the connector (A).

3.

Loosen the steering wheel bolt (B) three turns.

4.

Install a commercially available steering wheel puller (A) on the steering wheel (B).

5.

Free the steering wheel from the steering column shaft by turning the pressure bolt (C) of the puller.

Note these items when removing the steering wheel:

6.

Remove the steering wheel puller.

7.

Remove the steering wheel (A) from the steering column.

1.

Remove the steering wheel rear cover (A).

1.

Remove the audio remote/multi-information display switch (A).

1.

Measure the resistance between terminals No. 2 and No. 5 in each switch position according to the table.

2.

Measure the resistance between terminals No. 3 and No. 5 in each switch position according to the table.

3.

If the resistance is not as specified, replace the audio remote/multi-information display switch (A).

1.

Install the audio remote/multi-information display switch (A).

1.

Install the steering wheel rear cover (A).

1.

Make sure the front wheels are pointing straight ahead.

2.

Center the cable reel (A). Do this by first rotating the cable reel clockwise until it stops.

3.

Rotate the cable reel counterclockwise about three full turns. The arrow mark (B) on the cable reel label should point straight up.

4.

Position the steering wheel hub (A) so that it engages the pin (B) of the cable reel.

5.

Install the steering wheel (C) on to the steering column shaft.

NOTE: Do not tap on the steering wheel or the steering column shaft when installing the steering wheel.

6.

Install the steering wheel bolt (A), and tighten it to the specified torque.

7.

Connect the connector (B).

8.

Make sure the wire harness is routed and fastened properly.

NOTE: If you are replacing a deployed driver's airbag, inspect the cable reel for heat damage. If there is any damage, replace the cable reel.

1.

Place the driver's airbag (A) in the steering wheel.

2.

Tighten the new TORX bolts using a TORX T30 bit.

NOTE: Make sure the clearance (B) between the steering wheel and horn pad is the specified value.

3.

Connect the driver's airbag inflator connector (A) on the cable reel harness.

4.

Connect the horn switch connector (B).

NOTE: After reconnecting the negative cable to the battery, make sure the horn works properly.

5.

Install the access panel (C).

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery (B).

NOTE: Always connect the positive side first.

3.

Connect the negative cable and battery sensor (C) to the battery.

4.

Apply multipurpose grease to the terminals to prevent corrosion.

1.

Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.

2.

Turn the ignition switch to ON (II).

3.

Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC circuit troubleshooting.

1.

Park the vehicle on a flat and level surface, with the steering wheel in the straight ahead position.

2.

Select VSA ADJUSTMENT, then select ALL SENSORS with the HDS, and follow the screen prompts.

NOTE: See the HDS Help menu for specific instructions.

1.

Select EPS ADJUSTMENT, then select EPS STEERING ANGLE SENSOR VALUE CLEAR and follow the screen prompts on the HDS.

NOTE: See the HDS Help menu for specific instructions.