Honda Civic manuals

Honda Civic Service Manual: Carpet Removal and Installation (2-door A/T)

Honda Civic Service Manual / Body / Doors and Enclosures / Doors / Carpet Removal and Installation (2-door A/T)

847100

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Battery Terminal (SRS) - Disconnection

1.

Make sure the ignition switch is in LOCK (0).

2.

Disconnect and isolate the negative cable with the battery sensor (A) from the battery.

NOTE:

Always disconnect the negative side first.

To protect the battery sensor connector (B) from damage, do not hold it when removing the negative terminal.

Do not disconnect the battery sensor from the negative terminal (C).

3.

Disconnect the positive cable (D) from the battery.

4.

Wait at least 3 minutes before starting work.

2. Both Front Seat Belt Lower Anchor Bolts

Driver's side

Passenger's side

1.

Remove the lower anchor cap (A).

2.

Remove the lower anchor bolt (B).

3. Both Front Seats

1.

Remove both seat track end covers (A).

2.

The driver's seat is shown; repeat on the passenger's seat.

Front side

Rear side

3.

Remove the seat mounting bolts (A).

4.

The driver's seat is shown; repeat on the passenger's seat.

5.

Disconnect the connectors (A).

6.

Detach the harness clips (B).

7.

The driver's seat is shown; repeat on the passenger's seat.

8.

With the help of an assistant, carefully remove both front seats through the front door opening.

4. Rear Seat Cushion

1.

Remove the bolt (A) securing the rear seat cushion (B).

2.

While pushing down the rear seat cushion (A), pull the seat hook handles (B) to release the hooks (C).

3.

Remove the rear seat cushion.

5. Front Door Sill Trim - 2-Door

1.

Remove the cap (A).

2.

Remove the opener lock cylinder (B).

3.

Remove the screw (A).

4.

Remove the front door sill trim (A).

6. Front Door Sill Trim - 2-Door

1.

Remove the front door sill trim (A).

7. Both Kick Panels

Driver's side

Passenger's side

1.

Pull out both front door opening seals (A) as needed.

2.

Remove both kick panels (B).

8. Center Console Panel Assembly (Except '12M M/T)

1.

Detach the clips (A).

2.

Remove the center console panel (A).

3.

For some models: Disconnect the connector(s) (B).

9. Cup Holder Panel Assembly

1.

Remove the cup holder panel assembly (A).

10. Center Console

1.

Remove the bolts (A).

2.

Disconnect the connector (B).

3.

Remove the console box mat (A).

4.

Remove the bolts (B).

5.

Disconnect the connector (A).

6.

Remove the center console (A).

11. Steering Joint Cover

1.

Remove the steering joint cover (A).

12. Footrest

1.

Remove the lower clip (A) from the stud bolt (B) with a 6 mm hex socket wrench.

2.

Remove the upper clip (C) from the stud bolt (D) with a flat-tip screwdriver, then remove the footrest (E).

13. Floor Carpet - 2-Door (A/T)

1.

Remove the HVAC bracket (A).

2.

Disconnect the connectors (A), and detach the harness clips (B).

3.

Detach the harness clips (A).

4.

Detach the clips (A).

5.

Release the hook and loop fastener (B).

6.

Cut the carpet (C) in the area (D) as shown.

7.

Pull out the seat harnesses (E), then remove the carpet.

8.

If necessary, remove the floor mat holder (A).

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

1. Floor Carpet - 2-Door (A/T)

1.

If necessary, install the floor mat holder (A).

2.

When installing the new carpet, cut the carpet in the area (A) as shown.

3.

Pass the seat harnesses (B), then install the carpet (C).

4.

Install the hook and loop fastener (D).

5.

Install the clips (E).

6.

Install the harness clips (A).

7.

Connect the connectors (A), and install the harness clips (B).

8.

Install the HVAC bracket (A).

2. Footrest

1.

Install the upper clip (A) to the stud bolt (B).

2.

Install the lower clip (C) to the stud bolt (D), then install the footrest (E).

3. Steering Joint Cover

1.

Install the steering joint cover (A) in the sequence shown.

4. Center Console

1.

Install the center console (A).

2.

Connect the connector (A).

3.

Install the bolts (A).

4.

Install the console box mat (B).

5.

Connect the connector (A).

6.

Install the bolts (B).

5. Cup Holder Panel Assembly

1.

Install the cup holder panel assembly (A).

6. Center Console Panel Assembly (Except '12M M/T)

1.

For some models: Connect the connector(s) (A).

2.

Install the center console panel (B).

3.

Install the clips (A).

7. Both Kick Panels

Driver's side

Passenger's side

1.

Install both kick panels (A).

2.

Install both front door opening seals (B) as needed.

8. Front Door Sill Trim - 2-Door

1.

Install the front door sill trim (A).

9. Front Door Sill Trim - 2-Door

1.

Install the front door sill trim (A).

2.

Install the screw (A).

3.

Install the opener lock cylinder (A).

4.

Install the cap (B).

10. Rear Seat Cushion

1.

Install the hooks (A) to the rear seat cushion clips (B).

2.

Install the bolt (A) securing the rear seat cushion (B).

11. Both Front Seats

1.

With the help of an assistant, carefully install both front seats through the front door opening.

2.

Install the harness clips (A).

3.

Connect the connectors (B).

4.

The driver's seat is shown; repeat on the passenger's seat.

Front side

1n25mman

Rear side

5.

Install the seat mounting bolts (A).

NOTE: Tighten the bolts to the specified torque in the sequence shown.

Tighten the bolts by hand first, then tighten them to the specified torque.

Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the way back and tighten 1 and 2, then slide it forward and tighten 3 and 4.

6.

The driver's seat is shown; repeat on the passenger's seat.

7.

Install both seat track end covers (A).

8.

The driver's seat is shown; repeat on the passenger's seat.

12. Both Front Seat Belt Lower Anchor Bolts

Driver's side

Passenger's side

@@@

1.

Assemble the washer, the collar, and the bushing on the lower anchor bolt as shown.

NOTE: Apply medium strength liquid thread lock to the lower anchor bolt before reinstallation.

Driver's side

7m2nmn:mm

Passenger's side

unr:2inm,

2.

Install the lower anchor bolt (A).

3.

Install the lower anchor cap (B).

13. Battery Terminal (SRS) - Reconnection

(o.2ao.sam.

NOTE: If the battery performs abnormally, test the battery.

1.

Clean the battery terminals.

2.

Connect the positive cable (A) to the battery.

NOTE: Always connect the positive side first.

3.

Connect the negative cable and the battery sensor (B) to the battery.

NOTE: To protect the battery sensor connector (C) from damage, do not hold it when installing the negative terminal.

4.

Apply multipurpose grease to the terminals to prevent corrosion.

C-Pillar Trim Removal and Installation (4-door except Natural Gas models)
Removal SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Rea ...

Carpet Removal and Installation (4-door A/T)
847100 SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Bat ...

See also:

Honda Civic Owners Manual. About Open Source Licenses
To see the open source license information, follow these steps. Models with color audio system Press the MENU/CLOCK button.  Rotate to select Settings, then press .  Rotate to select OSS Licenses, then press . Models with Display Audio Select .  Select Settin ...

© 2016-2018 Copyright www.hocivic.com